• ベストアンサー
  • 困ってます

翻訳お願いします

When I make a heat sink for a C6 host I make the heat sink longer than the ones in the picture you sent me, you will not need the "pill" from the host as the heat sink will be in it's place and I machine a step in the end of the heat sink for a round 17.7mm driver to fit into unless your driver is a different size so let me know, 17.7mm is the size that is in a C6 pill.

共感・応援の気持ちを伝えよう!

  • 回答数1
  • 閲覧数32
  • ありがとう数1

質問者が選んだベストアンサー

  • ベストアンサー
  • 回答No.1
  • ddeana
  • ベストアンサー率74% (2977/4020)

C6用のヒートシンクを作る時、あなたが送ってくれた写真のものよりも長いヒートシンクを作りますが、ヒートシンクを決められた場所に収めてから、ヒートシンクの最後の部分に丸い17.7ミリのドライバーがピッタリとあうようにひとつ機械加工をほどこすので、ホストからの「ピル」は必要ありません。ただし、C6ピルにあうサイズは17.7ミリですがあなたのドライバーが違うサイズならお知らせください。 といった内容かと存じます。

共感・感謝の気持ちを伝えよう!

質問者からのお礼

ばっちりです。 回答ありがとうございました。

関連するQ&A

  • 翻訳お願いします

    The F25 copper heat sink will be $25.00 no I'll make it for you for $20.00 this time as you have bought from me before and I'm guessing you will again so a good deal for is in order for you so $20.00 for the F25 copper heat sink for postage it will be approx $15.00 and the paypal fees are figured on the total so I'm guessing approx $3.00 or less there.

  • 翻訳お願いします

    So did I mess up and just not put any screws in the L2 heat sink ?? it is drilled and tapped correct ? Sorry about that Can you tell me dose the holes for the set screws look bigger in the L2 heat sink than the holes in the F25 ? Think I used the larger size set screws in the L2, please let me know so I can send you the correct ones. Yes I still have the C6 host here that I made the copper heat sink to fit would you like it, it is $12.00 Let me know...

  • 翻訳お願いします

    Yes I make a heat sink for a C6 host in aluminum it is $15.00 and in copper it is $20.00 my heat sinks do not compare with ANY ONE else's as I make mine fit like a glove so the heat can get out and I put two set screws in every heat sink I make, there is no skimping on quality here ! I have yet to see a heat sink made by any one else here on LPF that is as good as mine !! When something cost cheap that is what you are going to get something cheap ! I have found over the years you usually get what you pay for

  • 翻訳お願いします

    When your L2N host arrives next week I will make a heat sink for it and in the mean time I'll make the F-25 heat sink, when they are both finished I'll PM you and you can pay then and I'll ship right away Sound good to you ?

  • 翻訳お願いします

    OK I have the aluminum one finished and the copper is all finished except for the set screws, I need to know if you like this length or if you would like it shortened a little as it's longer than the one you showed me by several mm. I left it this long because I felt the more heat sink you have the better it is for your laser diode but you may not like the look of it so I am giving you a chance to have it shorter if you like. Also I think these heat sinks may not fit your hosts as they were made to fit these hosts and you know I like to make them tight, for example the aluminum heat sink will go in the host that the copper heat sink was made for and it's a bit loose but the copper heat sink will not fit inside of the other host. There is about .005" difference in them so you will probably want these hosts they are $12.00 each that's my cost. Let me know about the length so I can finish it up and get it off to you

  • 翻訳お願いします

    That should work fine, you can put the driver in the pill it's big and made from brass so it should make a good heat sink. Since you will only be using one 26650 cell then you will not want an extension tube for this host, I did buy a couple of them just in case I have to go help a friend now so I will finish it tomorrow.

  • 翻訳お願いします

    So unless I have already given you prices (and I don't remember) this is what I have come up with now. L2 host and copper heat sink is $55.00 and the Hydra focus adapter is $25.00, the E2 host is $26.00 and the copper heat sink is $65.00 (normally I would charge $75.00 but you have been a good customer ) and the flat focus adapter is $20.00, the V5 driver with silicone wire leads is $28.00 I'll throw in the L2 battery contact for free and shipping to you is $24.00 and paypal fees are $10.00 for a grand total of $253.00 minus the $50.00 you already sent leaves a balance of $203.00. If that sounds correct to you please PP funds to: ****@gmail.com and I'll get this all packed up and on the way to you I hope this works for you if I have given you any other price please let me know

  • 翻訳お願いします

    The heat sink by it's self would be $75.00 but I need the host here to make the heat sink to get the very best fit. if it's a sloppy fit then the heat can not get out of the heat sink to the host.

  • 翻訳お願いします

    2つあります。 1...I have not reached you yet in my work log but decided you should not have to wait any longer so I am bumping you up I am starting on your F25 right now, please tell me what the second heat sink is to be made for I have forgotten now 2...I just found it, it's a L2 black host OK I'm making the copper heat sink for the F25 now and then a copper one for the L2 host, get back to you soon.

  • 翻訳お願いします。

    I have nothing made sitting on the shelf ready to go, every thing is made to order. There are many people on the list now to have heat sinks and other machined items made, if you get on the list right now it will be 4-5 weeks before I get to your name on the list. would you like to look at the models of hosts I have in stock now and that I can make you a heat sink for ? I can make you a complete kit of parts also if you like. let me know...