- 締切済み
翻訳お願いします
You have to remember if your drives both will be putting out 2000mA each then each one will be drawing 3000mA or around there so I would use no smaller than a 26650 cell or cells and I think 32650 would be nice if a good host can be found that is to your liking. The SK can take a 32650 if I put it in the lathe and take out about 0.25mm of aluminum from the inside. The two XB-2 drives I sent you are the very latest model they are capable of 4000mA each so with the proper heat sinking they may work for you. Do not try and run them above 2000mA with out heat sinking them, I do believe they have a built-in temp controller so if they get too hot they will shut down till they cool off, I'll check on that to be sure. The full back side needs to be in contact with a heat sink if your going to take one all the way to it's max current of 4000mA ! Hope this helps Let me know if you need any other info
- bonboy
- お礼率76% (549/719)
- 英語
- 回答数1
- ありがとう数2
- みんなの回答 （1）
- 専門家の回答
みんなの回答
- Nebusoku3
- ベストアンサー率38% (1441/3774)
やってもいいのですが、少し長いので翻訳サイトを紹介します。 どなたかからの受け売りですが 参考URL: http://translation.infoseek.ne.jp/ 比較的近い形の訳が出てくるようです。 後は実際にあわせて 意訳すれば OKでしょう。
関連するQ&A
- 翻訳お願いします。
OK then you have it, they are $30.00 and mine fit like a glove, you will see when you get your SAIK As far as I can tell no one else takes the time to make heat sinks fit like they should, most make them so they will fit ANY host of the same style and I guess for some that's good enough. I like my heat sinks to fit the host like a glove so the heat can get out You have a good day SAIK=LEDライトの名前
- ベストアンサー
- 英語
- 翻訳お願いします
OK I have the aluminum one finished and the copper is all finished except for the set screws, I need to know if you like this length or if you would like it shortened a little as it's longer than the one you showed me by several mm. I left it this long because I felt the more heat sink you have the better it is for your laser diode but you may not like the look of it so I am giving you a chance to have it shorter if you like. Also I think these heat sinks may not fit your hosts as they were made to fit these hosts and you know I like to make them tight, for example the aluminum heat sink will go in the host that the copper heat sink was made for and it's a bit loose but the copper heat sink will not fit inside of the other host. There is about .005" difference in them so you will probably want these hosts they are $12.00 each that's my cost. Let me know about the length so I can finish it up and get it off to you
- ベストアンサー
- 英語
- 翻訳お願いします
Sure I will do that for you but you have to realize there are other people in line right now waiting for me to make there heat sinks and other machined items, so it's not going to happen over night. Once I order the SAIK host it will be several weeks before it even gets here so it could be as much as 4-5 weeks before I can start on you copper heat sink. Of course there will be shipping from me to you, I don't pay to ship other peoples items to them. I would think the shipping will be approx $12.00 but I will only charge you the exact shipping cost after I weight the package. There will also be paypal fees they should be around $4.00 if all you are getting is the host and the heat sink. You could send the $90.00 now and that way I will get the SAIK ordered and your name written in my work log so that you are in line. And then when your SAIK arrives I will make the heat sink and you can decide if you need any other items and also get the balance payed at that time. Let me know so I can get it ordered
- ベストアンサー
- 英語
- 翻訳をお願いします！
日本語に訳していただけないでしょうか？ 宜しくお願いします！ They transform you spiritually and are karma. They make you the person you are today, and the person you will be when you meet. Each persons karma (development of soul and character) goes at its own pace, it cannot always be measured in years or days. It’s like reading a book, each chapter; a chapter of your life, the meeting is on a certain page but some people read the book faster, some slower. In theory you can hasten the meeting, you could get to the page quicker if you work on your karma, if you become the person your destined to be sooner. Just by having this reading done your are already step closer to that time than before.
- ベストアンサー
- 英語
- 翻訳お願いします
Yep they both look to be moving along just fine. It can be slow sometimes and it is yet past 30 days. Sometimes they take a little longer as well but not more than 45. If you can shoot me your email I can look up the order and have you check to make sure the addresses are correct.
- ベストアンサー
- 英語
- 翻訳お願いします。
I have nothing made sitting on the shelf ready to go, every thing is made to order. There are many people on the list now to have heat sinks and other machined items made, if you get on the list right now it will be 4-5 weeks before I get to your name on the list. would you like to look at the models of hosts I have in stock now and that I can make you a heat sink for ? I can make you a complete kit of parts also if you like. let me know...
- ベストアンサー
- 英語
- 翻訳お願いします
taro, That is the problem is your friend not me.! Good lasers take long time to build.! I cant deal with people that are im patient. You new from the beginning it was going to take long time because i did not have the hosts. I though the host will be in in Less then 3 weeks but it took nearlly 1 and 1 1/2 months. I know that you buy my lasers and re sell them to friend to make money and that is fine however you needed to tell your friends that it takes long time to build 3mode saik 1.7W-1.8W lasers. You know people sell lasers o this forum 3 a week and the look nice but there cheap junk inside. I put 1 laser up a week and its high quility. See the diffrence. I can tell you taro that dealing with you and your friend that you 2 have been the only too people to act like this. I hve never had anyone tell me iam slow, Not even jiro would say such a thing.! Because they know its not nice. Anyways, If you promise never to do such a thing again because if you do i will find out right away, But if you promise never to ask anyone to make a laser or laser heatsinks or parts that i make Iam will to forget about what happend iand start fresh. Let me know If you re Genue
- ベストアンサー
- 英語
- 翻訳お願い致します。
おおよその意味は変わるんですが、間違っているかも知れないので、翻訳お願いいたします。（アドレスの部分は、一部削除しています。） I'm OK with the price 680,000. Yen and condition you gave me and i will be paying through Bank i will be adding the 3.9% Bank surcharge to the total amount i will be paying you.. So i will be paying directly into your Bank account without any delay, and i hope you have a Bank account and if not you can easily create your Bank account here is my details below to show you that am seriously interested in your item Charlle Granndy Address : 1995・・・・ City : Shidler State : Oklahoma Zipcode : 74652 Country :USA So kindly get back to me with your Bank details like this below Account Name: Account Number: Bank Name: Bank code: Email Address: So kindly get back to me with your Home details like this below Full Name: Address: Phone Number: As soon as i receive this details from you, i will proceed with the payment immediately and i have already arrange for a private shipping agents that will come for the pick up of the item at your house door step and they will take care of the picking up document including the full information to pick up the item at your house door step. So I will need your home address as soon as the payment is made to you.. Best Regard.
- ベストアンサー
- 英語
- 以下の英文を日本語に翻訳して下さいますか？
Missions： Please refer to CHAPTER ５. Sorry to be DIRECT. I’m going to REPORT you when doing your translation. Mission 1→ Be sure to use both direct and reported speech in your assignment. I left both in the Japanese version, so if you just translate the sentences the way they are written, you will use both.
- ベストアンサー
- 英語
お礼
翻訳サイトありがとうございます。 大体わかりました。