• 締切済み

ブルースクリーンが出てしまいました

質問させてください。 以前より、パソコンを使っている最中にいきなり電源が落ちるという症状が発生し、先日ブルースクリーンが出てしまいました。 一度目に出た一昨日は、セーフモードで再起動をしてシステムの復元を行い、何とか通常起動することが出来ましたが、昨日パソコンを立ち上げた時にまた同じブルースクリーンが出てしまいました。 ブルースクリーンに書いてあった文章は以下に記載致しますので、症状と対処法をご教授頂ければ幸いです。 尚、OSはWindows XPです。 ご回答お待ちしております。 よろしくお願い致します。 A problem has been detected and windows has been shut down to prevent damage to your computer. PFN_LIST_CORRUPT If this is the first time you've seen this stop error screen, restart your computer.If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation,ask your hardware or software manufacturer for any windows updates you might need. If problem continue,disable or remove any newly installed hardware or software.Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components,restart your computer,press F8 to select Advanced Startup Options,and then select Safe Mode. Technical information: *** STOP:0x0000004E(0x0000008F,0x00029E0B,0x00029E0A,0x00000000) Beginning dump of physical memory physical memorydump computer. contact your system administrator or technical support group for further

みんなの回答

  • bunjii
  • ベストアンサー率43% (3589/8248)
回答No.3

使用の頻度によりますが、そろそろ買い替えの時期が来たのではないでしょうか? >以前より、パソコンを使っている最中にいきなり電源が落ちるという症状が発生し、 そのような時期に原因究明しておくべきでした。 HDDの一部に読み取り不良が発生している可能性があります。 また、RAMのエラーも無いとは言えません。 データの救出の必要が無ければリカバリ(工場出荷状態に戻す)またはOSの再インストールを行ってみるのも一つの選択肢です。 家電製品の寿命は5~6年とされていますので、パソコンも同等と考えて買い替えを検討してください。

  • m_and_dmp
  • ベストアンサー率54% (974/1797)
回答No.2

ブルースクリーンエラーに対する明快な(ピンポイントの)対処方法を見たことがありません。多分マイクロソフトもピンポイントの解を与えてはくれないと思います。 経験的に、ハードウエアの不具合、ハードウエアの相性(製造者が相性のせいにして責任を回避するのはいけないと思うのですが)、デバイスドライバの不適合などで起きるようです。 ハードウエアの中でもUSB接続機器は相性が悪いものが多いのか、ブルースクリーンエラーを起こすものがありました。 メモリーが不具合の時は、「PAGE FAULT IN NONPAGED AREA」というメッセージが出ることが多いと聞いています。 しかし、これが出たら間違いなくメモリーというわけではありません。後述のとおり、私の場合はそれが出ましたがメモリーではなかったからです。また、それが出ないからメモリーではないということでもないと思います。 私は数ヶ月前からブルースクリーンエラーに悩まされ、CPUとオンボードのデバイス(BIOSで無効にすることができるものもありますが、取り外すことはできません。)を除いて交換できるものはすべて交換してみました。メモリーはMEMTEST86+で10ラウンドテストしてノーエラーのものに交換しました。あとはCPUとマザーボードしかない状況で、CPUを交換したところ、直りました。 結論は、外せるものは全部外して、一つ取り付けては様子を見るしかないということです。

noname#146604
noname#146604
回答No.1

おそらくメモリの問題ですね。 別のメモリに交換しましょう。

関連するQ&A

  • ブルースクリーンが出てしまいます

    youtubuを利用している時に主になります。 以下がブルースクリーンの内容です。 A problem has been detected and windows has been shut down to prevent damage to your computer. IRQL NOT LESS OR EQUAL If this is the first time you've seen this stop error screen,restart your cmputer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is proqerly installed. If this is a new installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software.Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components,restart your computer,press F8 to select Advanced Startup Options,and then select Safe Mode. Technical information: STOP: 0x0000000A(0x000000D7,0x00000002,0x00000000,0x804ED977) Beginning dump of physical memory Physical memory dump complete. Contact yor system administrator or technical support group for further assistance. Windows XPを使ってます。 このブルースクリーンが出ないようにするには、どうすればいいのか教えてください。よろしくお願いします。

  • ブルースクリーンになった

    たびたびブルースクリーンになりますが、 今回は *** STOP: 0x0000001D(0xB64F736A,0xBACD79B4,0x00000000) 前回は A problem has been detected and wiondows has been shut to down to prevent damage to your computer. ORQL-NOT-LESS-OR-EQUAL If this si thefirst time you`ve seen this stop error screen, restart your computer. If this screen again,follow these steps: check to meke sure any new hardware or spftware is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer, press F8 to select advanced startup option, and then select safe mode. Technical information: *** STOP: 0x0000000A (0x00000010,0x00000002,0x00000001,0x8051873C) beginning dump of physical memory physical memory dump complete. Contact your system administrator or technical support group for further assistance. 教えてください、お願いします。

  • ブルースクリーンが起こってしまったのですが

    質問をさしてもらい ブルースクリーンということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか (色々と対処をしてもまた別の原因でブルースクリーンが起こってしまった場合はどうすればよいでしょうか) A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: luafv.sys IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x6c006160, 0x0000001b, 0x00000001, 0x82ef55ce) *** luafv.sys - Address 0x91be4036 base at 0x91bdb000 DateStamp 0x47918afb 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: tmcomm.sys PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000050 (0xd76c5da4, 0x00000000, 0x807c6d5b, 0x00000002) *** tmcomm.sys - Address 0x8f28ce4b base at 0x8f287000 DateStamp 0x49d4727e

  • ブルースクリーン

    WinXPがウイルスでブルースクリーンが表示される様になってしまいました。 まずはセーフモードから起動するかという画面が表示されるのですが、セーフモードを選んでも起動せずにブルースクリーンが表示されます。 特に重要なデータもないのでOS再インストールしようと思うのですが、DVDドライブ起動をしようとしても同じ画面が表示されてしまいます。もしかしたらBIOSまでおかしくなってしまったのでしょうか? 以下ブルースクリーンの警告文です。 A problem has been detected and windows has been shut down to prevent damage to your computer. PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed.If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode. Technical information: *** STOP: 0×000000050 (0×F78CB800,0×00000001, 0×80583EC5, 0×00000000) フォーマットも辞さないので、何かいい方法ないでしょうか?? よろしくお願いします。

  • ブルースクリーンが出て・・・

    A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntoskrnl.exe BAD_POOL_HEADER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000019 (0x0000000000000022, 0x0000000000000000, 0x0000000000000000, 0x0000000000000000) *** ntoskrnl.exe - Address 0xfffff80003eba700 base at 0xfffff80003e4a000 DateStamp 0x4d9fdd34 というブルースクリーンが出てたまにPCが落ちます 対処法を教えてくださいお願いします

  • ブルースクリーンが起こってしまったのですが

    質問をさしてもらい ブルースクリーンということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: USBPORT.SYS DRIVER_IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x000000d1 (0x0000008c, 0x00000002, 0x00000000, 0x8fbc62c4) *** USBPORT.SYS - Address 0x8fbc62c4 base at 0x8fbc0000 DateStamp 0x49e01fcf 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x00000063, 0x0000001b, 0x00000001, 0x82ec15ce) *** ntkrnlpa.exe - Address 0x82e67fd9 base at 0x82e1a000 DateStamp 0x4cb710d6 三つめ A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: Ntfs.sys NTFS_FILE_SYSTEM If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000024 (0x001904aa, 0xbf7b7a18, 0xbf7b7714, 0x82ebe22c) *** Ntfs.sys - Address 0x8b41cfff base at 0x8b403000 DateStamp 0x49e0192a

  • ブルースクリーン

    A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntoskrnl.exe ATTEMPTED_SWITCH_FROM_DPC If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x100000b8 (0xb2cb3490, 0x80ccca48, 0xb35d7000, 0x00000000) *** ntoskrnl.exe - Address 0x824c0246 base at 0x82418000 DateStamp 0x4a77feb3 ↑の様なブルースクリーンが出て困っております。 ntoskrnl.exeが原因なのでしょうが、何が何だか分かりません。 至急解決策をお願いします。

  • ブルースクリーン現象になりました

    質問をさしてもらい ブルースクリーン現象ということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x9589a9b8, 0x00000002, 0x00000000, 0x82ebb60b) *** ntkrnlpa.exe - Address 0x82e4ffd9 base at 0x82e02000 DateStamp 0x4cb710d6 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x00000000, 0x0000001b, 0x00000000, 0x82e95c94) *** ntkrnlpa.exe - Address 0x82e9bfd9 base at 0x82e4e000 DateStamp 0x4cb710d6 三つめ A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe CACHE_MANAGER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information:

  • 光学ドライブを使うとブルースクリーンに・・・。

    光学ドライブを使おうとすると、ブルースクリーンになってしまうので困っています。 A problem has been detected and windows has been shut down to prevent damage to your computer. Machine check exception. If this is the first time you are seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable Bios memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer, press F8 to select Advanced startup options, and then select safe mode. Technical information. Stop: 0 ×0000009C (0×00000004,0×8054F5F0,0×B2000000,0×00070F0F) Beginning dump of physical memory physical memory dump complete. Contact your system administrator or technical support group for further assistance. この様な、メッセージが出ます。 ウインドウズを時間を空けて起動してもブルースクリーンになってしまいます。 取り敢えず、光学ドライブを使わなければ、ブルースクリーンにならないのですが、何か、対処の方法は、ないでしょうか? ご教示、よろしくお願いします。

  • ブルースクリーンが出てしまう

    2・3日前から、PCを起動してもブルースクリーンが出てきて動かなくなってしまうので困っています。 まず異常が起こる前の状態なんですが、スパイウェアが入ってしまったのでSpybotを使って駆除しました。 その後は普通に起動していたのですが、またスパイウェアのようなものが入って動かなくなってしまったので、一度強制終了しました。 そしてまた起動してみたら、黒い選択画面が出てくるようになりました。 その後は、どの項目を選択してもブルースクリーンになります。 ブルースクリーンの英文は、これです。 (重要ではなさそうな部分は、日本語で簡単に書きます) 『A problem has been detected and windows has been shut down to prevent damage to your computer. (再起動してもこの画面なら以下の指示に従って下さい) Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory ortions such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced startup options, and then select Safe Mode. Technical information: STOP: 0x000000ED (0x8172E790,0x0000032,0x00000000,0x00000000)』 ちなみに、セーフモードでも起動してみようとしましたが作業途中でまたブルースクリーンに戻ってしまいます。 本当に困っています;; 分かる方いましたら、ぜひアドバイス下さい!! よろしくお願いしますm(_ _;)m