WindowsXP青い画面エラーの解決方法

このQ&Aのポイント
  • Windowsを開く際に青い画面が表示されるエラーが発生しています。この記事では、WindowsXPで発生する青い画面エラーの解決方法について詳しく説明します。
  • エラーが発生した際に表示される英語のメッセージは、コンピューターの保護のためにWindowsがシャットダウンされたことを示しています。このエラーが初めて表示される場合は、コンピューターを再起動してください。もし再度この画面が表示された場合は、以下の手順に従ってください。
  • まず、ハードウェアメーカーが提供するシステム診断ユーティリティを実行してください。特に、メモリのチェックを実行し、故障しているか不一致しているメモリを確認してください。また、ビデオアダプターを変更してみてください。また、最近インストールしたハードウェアやドライバーを無効化または削除してください。新しくインストールしたソフトウェアも無効化または削除してください。安全モードを使用してコンポーネントを削除または無効化する必要がある場合は、コンピューターを再起動し、F8キーを押して高度な起動オプションを選択し、安全モードを選択してください。
回答を見る
  • ベストアンサー

Windows XP

ここ最近、Windowsを開こうとすると、青い画面が出てきます。 「 A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Run a system diagnostic utility supplied by your hardware manufacturer. In particular, run a memory check, and check for raulty or mismatched memory. Try changing video adapters. Diseble or remove any newly installed hardware and drivers. Disable or remove any newly installed software. If you need o use safe mode to remove or disable components, restart your computer, press F8 to select Advanced startup options, and then select safe mode. Technical information: STOP: 0×0000007F  ( 0×0000000D, 0×00000000, 0×00000000, 0×00000000)  」 と英語が書いてあります。 3日経っても直りません。 心当たりがあると言えば、iTunesがエラーになったので、アンインストールの手続きをしたことです。 どうやったら直りますか? お願いします。

質問者が選んだベストアンサー

  • ベストアンサー
  • g_liar
  • ベストアンサー率52% (382/728)
回答No.3

STOP: 0x0000007Fが出てることからハードウェア障害の可能性もありますが、まずはセーフモードで起動してみて、チェックディスクやシステムの復元を行ってみましょう。 Windows XP を セーフ モードで起動する方法 http://support.microsoft.com/kb/880414/ja Windows XP でディスクのエラーをチェックする方法 http://support.microsoft.com/kb/315265/ja Windows XP を以前の状態に復元する方法 http://support.microsoft.com/kb/306084/ja これでダメなら必要なファイルをバックアップして、OSのリカバリ。 それでもダメなら修理or買い替えです。

sora4033
質問者

お礼

ありがとうございました。

その他の回答 (3)

  • hizaore
  • ベストアンサー率38% (124/321)
回答No.4

英語を読んで,まずはその通りにするんですよ. 定型文であっても,多くの回答は書かれている内容を日本語で個別に回答してくれているだけのことが多いです. 英語を全然習ったことが無く,読めないなら質問も仕方ないかもしれません. ここまで転記する努力ができるなら,書いてあることを訳すほうがずっとラクだと思います.

sora4033
質問者

お礼

ありがとうございました。

  • violet430
  • ベストアンサー率36% (27472/75001)
回答No.2

http://support.microsoft.com/kb/137539/ja 故障が疑われます。 データをバックアップしてOSを再インストールし、再現するか確認した方が良いです。再現するなら故障とみます。

sora4033
質問者

お礼

ありがとうございました。

  • Yodo-gawa
  • ベストアンサー率14% (133/944)
回答No.1

HDDのデータだけバックアップして、可能ならばリカバリしましょう。 それで駄目なら諦めた方が良さそうです。時間をおいたからと言って、 改善されるわけではありません。

sora4033
質問者

お礼

ありがとうございました。

関連するQ&A

  • windows XP

    前にも同じような質問をしましたが、 最近、windowsを開こうとすると、青い画面が出てきます。 A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Run a system diagnostic utility supplied by your hardware manufacturer. In particular, run a memory check, and check for raulty or mismatched memory. Try changing video adapters. Diseble or remove any newly installed hardware and drivers. Disable or remove any newly installed software. If you need o use safe mode to remove or disable components, restart your computer, press F8 to select Advanced startup options, and then select safe mode. Technical information: STOP: 0×0000007F  ( 0×0000000D, 0×00000000, 0×00000000, 0×00000000)  ちなみに英語は読めません。 心当たりはiTunesがエラーになったので、項目を削除したことです。 たまに黒い画面に日本語で「セーフモードで起動する や、 通常起動する 」などと書いてある画面がでてきます。 セーフモードで項目を復元しようとしても、再起動されたときにまた青い画面に戻ってしまいます。 どうすればいいんでしょうか?

  • windows xpに関して質問です。

    windows xpに関して質問です。 起動中に、パソコンがジーっと音をたて、突然フリーズしバックがブルーの画面になります。 そこに以下の様な文章が書かれています。 A problem has been detected and windows has been shut down to prevent damage to your computer. KERNEL_STACK_INPAGE_ERROR If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer,press F8 to select Advanced Startup options, and then select safe memory. 文章は以上です。 何か設定で改善出来るのでしょうか?

  • Windows XPのアップグレードについて

    Win98SEからのアップグレードなのですが、セットアップの途中の最初の再起動の際、画面が青くなり、下記ような文章が表示されました。私には、さっぱり理解できません。 Meからのアップグレードでも、同じ現象でした。HDDをフォーマット後、新規のセットアップでもだめでした。どなたか、このPCでの、XPのセットアップの方法を教えてください。 自作PCの仕様 ・CPU Pentium(3) 866MHz ・HDD IBM DTLA307020 20GB ・マザー Aopen AX3SPro (BIOS R1.00) ・ビデオカード Aopen Pa256MX ・メモリー 384MB A problem has been detected and windows has been shut down to prevent damage to your computer. UNMOUNTABLE_BOOT_VOLUME If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hard ware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode . Technical information: ** STOP: 0x000000ED (0x82B9AA60,0xc0000102,0x00000000,0x00000000)

  • BIOSを元にもどす方法

    現在、DELLのInspiron530を使っているのですが、 BIOSのバージョンを1.00から1.05にバージョンアップしたら、 パソコンをスリープ状態から起動するたびにBlueScreenになり、  A problem has been detected and windows has been shut down to prevent damage to your computer.   BAD_POOL_CALLER  If this is the first time you've seen this stop error screen,restart your computer.If this screen appears again,follow these steps:  Check to make sure any new hardware,or software is properly installed.   If this is a new installation, ask your hardware or software, manufacturer for any windows updates you might need.  If problems continu,disable or remove any newly installed hardware or software.  If problems continue, disable or remove any newly installed hardware or software.  Disable BIOS memory options such as caching or shadowing.  If you need to use safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select safe mode. (以下略) という表示が出て、強制再起動になる、という症状が出るようになってしまいました。 できれば以前のバージョンにもどしたいのですが、どうやれば戻すことができるのかわかりませんでした。 だれかわかる人いたら教えてください(>_<)

  • Windows XPが起動しません

    会社のノートパソコンWindowsXP(HP社製 中身はCompaq nc4200)ですが 完全にシャットダウンせずに フタを閉じ、持ち歩くことを繰り返していたのですが ある時、PCを開こうとするとパスワードは入力できるものの次の画面で「safe mode」の画面が表示されるようになりました。前回終了時の画面に戻す等やってみたのですが 何度やっても その後 青い画面に 次のような文面が表示されます。 「A problem has been detected and windows has been shut down to prevent damage to your computer. UNMOUNTABLE BOOT VOLUME If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again,follow these steps Check to make sure any new hardware or software is properly installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer,press F8 to select Advanced Startup Options,and then select Safe mode. Technical Information STOP 0X000000ED (0X82F248DO,0XC000009C,0X00000000,0X00000000) この状態だと やはり ハード自体もしくはソフトの故障でしょうか? 保存していたデータすべて消えてしまうのでしょうか? パソコンは エクセル、ワード等は使いこなしているものの本体のことに関しては ほとんど素人ですので 精通している方がいらっしゃれば是非、状況及び解決策を教えていただけないでしょうか? よろしくお願いします。

  • シャットダウン時に青画面+英文

    買って半年も経っていないノートパソコンなのですが、昨日シャットダウンしようとしたところ、なかなかシャットダウンされず私はそのまま寝てしまいました。ところが今日の朝起きてみると、青画面に大量の英文が映し出されていて、とても慌てました。画面には A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen restart your computer. If this screen appears again,follow these steps. Check to make sure any new hardware or software is properly installed.If this is anew installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadwing. If you need to use safe mode to remove or disable computers,restart your computer,press F8 to select Advanced startup options,and then selest safe mode. と表示されていました。 機械的な面にはあまり詳しくないので、どうしてよいかわからず、とても困っています。よろしくお願いします。

  • ウィンドウズが、何もせずに突然再起動してしまいます。

    つい最近から、ウィンドウズが突然再起動されるようになってしまって、システムの復元をしたのですが、それでも直りません。 再起動をしないように設定したら、青い画面でメッセージが出てきました。(下の英文全てです。) 現状では、いつエラー画面が出るか、ヒヤヒヤしています。 この画面は、何を意味しているのでしょうか、また、可能ならばその解決策を教えていただけると大変助かります。 A problem has been derected and windows has been shut down to prevent damage to your computer. PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen,restart your conputer. If this screen appers again,followthese steps: If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable conponents,restart your computer,press F8 to select Advanced Startup Options,and then select Safe Mode. Technical information:

  • Windows7 ブルースクリーンについて

    先日PCを自作したのですが、シャットダウンするときに100%ブルースクリーンになります。 画面には下記のように表示されます。 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000050 (0xfffff888037f9428, 0x0000000000000000, 0xfffff880037f680a, 0x0000000000000005) *** - Address 0x0000000000000000 base at 0x0000000000000000 DateStamp 0x00000000 いろいろ調べて、試してみてもなかなか有効な解決方法がが見つかりません。 解決するために御助力していただけたら幸いです。 どうかよろしくお願いしますm(_ _)m

  • XPが起動できない

    普通に使っていたのですが、突然ブルー画面で「A probem has been detected and windows has been shut down to prevent damege to your computer. UNMOUNTABLE_BOOT_VOLUME If this screen appears again, follow these steps: check to make sure any new hardware of software is proberly installed. If this is a new installation, ask your hardware of sortware manufacturer for any windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select safe mode. Technical information: *** STOP: 0x000000ED (0x82FEB3D8, 0xC0000006, 0x00000000, 0x00000000)」となり、以降セーフモードも含めてWindowsが起動できなくなりました。松下のCF-W2ですが、リカバリDVDがないのでオークションで探しています。どうしたら良いか、回復方法を教えて下さい。

  • windows7 ブルースクリーンで困っています。

    ブルースクリーンで困っています。 Technical infomation: STOP:0x0000007F (0x00000008,0x807C9750,0x00000000,0x00000000) 文中に上記テクニカル インフォメーション コードがあります。 再起動はできますが、しばらくすると、ブルースクリーンになります。一応、文面すべては下記の通りです。 A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first you've seen this stop error screen,restart your computer. If this screen appears again,follow these steps: Run a system diagnostic utility supplied by your hardware manufacturer. In particular,run a memory check,and check for faulty or mismatched memory.Try changing video adapters. Disable or remove any newly installed hardware and drivers.Disable or remove any newly installed software. If you need to use safe mode to remove or disable components,restart your computer,press F8 to select Advaced Startup Options,and then select Safe Mode. Technical infomation: STOP:0x0000007F (0x00000008,0x807C9750,0x00000000,0x00000000) Collecting data for crash dump... Initilizing disk for crash dump... Beginning dump of physial memory. Dumping physical memory to disc: 100 Physical memory dump complate. Contact your system admin or technical support group for further assistance. よろしくお願いします。