• 締切済み

エラー多発

PCを機動し5分ほど使用していたら以下のようにエラーが表示されてしまいました。 一週間ほど前から機動し少しすると再起動をするといった症状がでていました。 今現在は電源を入れてもOS機動画面にすらいかなくただファンがずっと回っている状況です。 どうなってしまったのでしょうか?? A problem has been detected and windosw has been shut down to prevent damege to your computer. BAD_POOL_HEADER if this is the first time you've seen this Stop error screen, restart your computer. if this screen appears again, follow these steps : check to make sure any new hardware or software is properly installed. if this is a noe installation, ask your hardware or software manufacturer for any windows updates you migth need. if problems continue, disable or remove any newly installed hardware or software, Disable BIOS memory options such as caching or shadowing. if you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced Startup Options, and then select Safe Mode. Technical infomation: ''' STOP : 0x00000019 (0x00000020,0x89641F00,089641F30,0x0A060001) Beginning dump of physical memory physical memory dump complete. Contact your system administrator or technical support group for further assistance.

みんなの回答

  • violet430
  • ベストアンサー率36% (27472/75001)
回答No.5

HDDかマザーボードが故障しています。 メーカ製ならパソコンメーカへ修理を依頼して下さい。

  • D9150
  • ベストアンサー率21% (36/167)
回答No.4

>BAD_POOL_HEADER の部分が↓になってしまいました。 DRIVER_IRQL_LESS_OR_EQUAL STOPコードは同じですか? メッセージどおりIRQの衝突等の不具合が生じております。 マニュアル等確認のうえ、NECサポートへ連絡を

  • kentan384
  • ベストアンサー率35% (781/2203)
回答No.3

遅延書き込みエラーですね。 BAD_POOL_HEADER もし、スキャナとカメラの接続時にエラーが出たなら  の  とおりですが、・・・・・この場合、電源を入れる前に接続しないということと問題のハードを繋がない。カメラですから、リムーバブルディスクも含むと思います。でもそうじゃないと思うのですが。 だって、 >電源を入れてもOS機動画面にすらいかなく ということはBIOSにまで見放されているわけで、つまりデバイス、ドライバを読み込むことができない。 でも、遅延書き込みエラーですから やはり、私は、ハードディスクに問題が発生しています。になります。 エラー定義は、指定されたディスクの領域またはトラックが見つかりません。です。 回避法は、HDDの交換もありです。ということで。

subaru3777
質問者

補足

BAD_POOL_HEADER の部分が↓になってしまいました。 DRIVER_IRQL_LESS_OR_EQUAL

  • D9150
  • ベストアンサー率21% (36/167)
回答No.2

コピペ誤りました。 >HDDで不具合が発生しております。 スルーを。 こちらで http://detail.chiebukuro.yahoo.co.jp/qa/question_detail/q1114223071 つぎはなにかな

  • D9150
  • ベストアンサー率21% (36/167)
回答No.1

Vostro 420ご購入なさいましたか? メッセージどおり不具合が生じております。 マニュアル等確認のうえ、サポートへ連絡を HDDで不具合が発生しております。

関連するQ&A

  • 突然のERRORどうすればよいでしょう?

    A problem has been detected and windows has been shut down to prevent damage to your computer. A process or thread crucial to system operation has unexpectedly exited or been terminated. If this is the first time you've seen this stop error screen,restart your computer. If this scrreen appears again, follow these steps: Check to make sure any new hardware or software is properly anstalled. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need, If problems continue, disable or remove any newly installed hardware or software, Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode, Technical information: STOP: 0x000000f4(0x00000003,0x811BADAO,0x811BAF14,0x805FBF88) Bginning dump of physical memory physical memory dump complete. Contact your system administrator or technical support group for further assistance. 上記メッセージ(誤字脱字があるかも知れませんが) 一度電源を落としてセーフモードでシステムの復元を試みてもまた同じエラーが出ます。どうしたらよいでしょう。XP(HE)SP2 

  • ブルー画面エラー

    このような画面がでてしまいました。 どうすればよいのでしょうか。 よろしくお願いします。 a problem has been detected and windows has been shut down to prevent damage to your computer. page_fault_nonpaged_area if this is the first time you've seen this stop error screen, restart your computer. if this screen appears again, follow these steps: check to make shre any new hardware or software is properly installed. if this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. if problems continue, disable or remove any newly installed hardware or software. disable bios memory options such as caching or shadowing. if you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select safe mode. technical information: stop: 0x00000050 (0xE14D4810,0x00000000,0x8055259a,0x00000001) Beginning dump of physical memory dumping physical memory to disk: 24

  • ブルースクリーンのエラーメッセージに・・・

    印刷をしようとすると下の様なエラーメッセージが出てしまいます。 いろいろ調べてみたのですが解決法がよくわからず困っています・・ どなたかわかる方お願いします。 A problem has been decated and windows has been shut down to prevent damage to your computer. BUGCODE_USB_DRIVER If this is the first time you`ve seen this stop error screen, restart your computer. If this screen appers again, follow these steps: Check to make sure any new hardware or software is propery installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as catching or shadowing. If you need to use safeMode to remove or disable components, restart your computer, press F8 to select Advanced start up options, and then select safeMode. Technical information Stop:0x000000FE(0x00000005,0xFEBC30E0,0x808624C2,0xFEF4D518) Begining dump of physical memory Physical memory dump complete. Contact your system administrator technical support group for further assistance. です。 情報としては ・Windows XP ・印刷時以外は起こらない よろしくお願いします。

  • パソコンがよくエラーを起こします

    インターネットに接続するとよくブルースクリーンが出ます。 エラーの内容はこれです。 A problem has been detected and windous has been shut down to prevent damage to your computer. IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is property installed. It this is a new installation,ask your herdware or software mahufacturer for any windous updates you might need. If problems continue,disable or remove any newly in stalled herdware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer,press F8 to select Advanced startup options,and then select safe Mode. Technical information: STOP:0X0000000A(0X00000000,0X00000002,0X00000000,0X804E2C37) Beginning dump of physical memory physical memory dump complate. Contact your system adminstrator or technical support group your system administrator or technical support group for further assistance. って出るんです! どうしたらいいんでしょうか!? 機種はNECのVALUESTARです。 WindowsXPです。 3年使ってます。 誰か回答お願いします!!

  • このようなエラーがでて困っています

    A problem has been delected and windows has been shut down to prevent damage to your computer. IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer.If this screen appears again,follow thiese steps: Check to make sure any new haedware or software is properly installed. If this is a new installation,ask your hardware or software manu facturer for any windows updates you might need. If problem continue disable or remove any newly installed hardware or software,Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable computers,restart your Computer,press F8 to select Advanced start up options,and then select safe mode. Technical information: ☆☆☆ STOP:0x0000000A(0x00000000,0x0000001c,0x804FCEE4) Beginning dump of phy sical memory. Physical memory dump complete Contaet your system administrater or technieal support group for further assistance というエラーです。解決方法または出なくなる方法を教えてください

  • 0x0000000Aエラー

    最近頻繁にブルーバック画面になります OS起動中または起動後です。 OSはWindows XPのSP2です メッセージは以下のとおりです A Problem has been detected and windows has been shut down to prevent damage to your computer. IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer.If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed.If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select safe mode. Technical information: STOP:0x0000000A(0xFFFE8080,0x00000002,0x00000001,0x806ED2DC) Beginning dump of physical memory Physical memory dump complete. Contact your system administrator or technical support group for further assistance. Web検索などしてみましたがよくわからなかったので質問させていただきました。よろしくお願いします

  • Windowsが立ち上がらずエラーメッセージが出ます

    今まで普通に使っていたのですが、朝パソコンをつけて立ち上げようとしたところ、Windowsが立ち上がらずエラーメッセージがでます。 以下がメッセージです。 A problem has been detected and windows has been shut down to prevent damage to your computer. PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen, restart your computer. If this screen appears agein, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer, press F8 to select Advanced startup options, and then select safe mode. Technical indormation: ***STOP:0x00000050 (0xCABE5001,0x00000001,0x8065965E,0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact your system administrator or technical support group for further assistance. 以上です。 最初はこの画面が一瞬だけ表示され再起動を繰り返していましたが 他の方の質問などを読み、F8をおして、 再起動を繰り返さないを選んだところとまりました。 セーフモードでの起動も試みましたが、 黒い画面のままとまり、起動はできませんでした。 ハードディスクが壊れてしまったのでしょうか? もうこのパソコンは使えませんか? どなたかご存知の方がいらっしゃれば教えてください。

  • パソコンが突然エラーが表示され使用できなくなります

    パソコンを使用していると突然画面いっぱいに下記のようなメッセージが出て使用できなくなります。強制終了して再起動し、ウィルススキャンしましたが、ウィルスは検出されてません。半月ほど前に、パソコンが突然シャットダウンしたりして不安定な状態があったのですが、最近は落ち着いていました。 古いパソコンなのでもう寿命でしょうか? 何か、確認方法があれば押して下さい。 パソコン:SONY VAIO PCV-RZ50 表示されたメッセージ A problem has been detected and windows has been shut down to prevent damage to your computer. BAD POOL HEADER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps. Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components,restart your computer,press F8 to select Advanced Startup options,and then select Safe Mode. Technical information; STOP: 0x00000019(0x00000020,0x896784A8,0x89678510,0x0A0D0000) Beginning dump of physical meory physical memory dump complete. Contact your system administrator or technical support group for further assistance.

  • ブルースクリーンエラーが出ます。

    ブルースクリーンエラーが出ます。 あるオンラインゲームをプレイしていると突然ブルースクリーンエラーが起こります。 何時間も出ないときもあれば、数分で出るときもあったりします。 全く知識がないためわかる方ご指導お願い致します。 A problem has been detected and windows has been shut down to prevent damage to your computer. The video memory manager has encountered an unexpected fatal error. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components,restart your computer,press F8 to select Advanced Startup Options,and then select Safe Mode. Technical information: *** STOP: 0x0000010E (0x0000001E,0x00000000,0x00000000,0x00000000) Collecting data for crash dump... Initializing disk for crash dump... Beginning dump of physical memory. Dumping physical memory to disk: 100 Physical memory dump complete. Contact your system admin or technical support group for further assistance. 以上のような文字が出ます。 宜しくお願い致します。

  • ブルースクリーンエラー

    少し前に質問させてもらったのですが、やはりまだ頻繁にでるので質問させてください。 ログをとったので対処法を教えてもらえないでしょうか? よろしくお願いします PAGE_FAULT_IN_NONPAGAED_AREA If this is the first time you're seen this stop error screen,restart your computer,If this screen appears again,fallow these steps: check to make sure any new hardware or software is properly installed. Ifthis is a new istallation,ask yore hardware or software manufacturer for any windows updates you mightneed. If problems continue,disable or remore any newly installed hardware or software,Disable BIOS memory options such as caching or shadowing. If you need touse sofeMode to remove or disable components,restart your computer,press F8 to select Advanced startup options,and then select safeMode. Technical in for mationi *** Stop:0x00000050(0xBAO0154,040000000,0x8058388F,0x00000000)