• 締切済み

モニターの表示がおかしくなったり、電源が落ちてしまいます。

はじめて投稿します、 分かる範囲で調べて触ってみたのですが手に負えず 修理に出そうかとは思っているのですが、どこが悪いのかだけでも 何か分かればと思い質問させていただきました。 よろしくお願いします。 今、使ってるPCは、 PC型番:PC-GV30V3ZE1 NEC VALUESTAR G(タイプL) メモリー:1024MB DDR SDRAM(512MB X 2) ハードディスク:250GB OS windows XP home sp1 モニター:F17R51 TFT液晶 2005.11 購入と言う内容です。  ある日、PC起動中に、突然モニター画面が真っ黒になり (電源スタンバイ状態、モニターのオレンジライト点灯、 PC本体は、電源落ちず。) あれ?おかしいなあ??と思いつつも使い続けていましたが そのうちにと言うか早々に症状が頻繁に出るようになりました。 症状が出るのは、電源ON後5-20分後ぐらいですが 時には、数分で再起動が掛かり、その後、上記症状となり あとは、何をしても動かなくなる事もありました。 また、別症状として、縦方向に10mm間隔ぐらいで筋が入り かつ画像が乱れて読み取りが出来ない状態になる。 (今、現在は、こちらの症状の方がメイン) さて、どうしたものかと思いつつ ・三年間放置していたケース内の沢山のホコリの除去 ・メモリーの差し換え、片側抜きして様子を見るも改善なし。 ・違うと思いつつも新しいHDDへの変更 などしましたが変わりなく。 最後の手段で再セットアップを試みましたが 作業の途中で下記記メッセージが出て 数分後には、上記にある 縦方向に10mm間隔ぐらいで筋が入り かつ画像が乱れて読み取りが出来ない状態になり お手上げ状態です。 マザーボードなのか?CPUに原因があるのか? はたまた、違う事なのか? お知恵を拝借させてくださいませ。 a problem has been detected and windows has been shut down to prevent damage to your computer. PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software . Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select safe Mode. Technical information: ***STOP:0X00000050(0XFE577A60,0X00000000,oX8082D43D,0X00000000)

みんなの回答

  • beat15th
  • ベストアンサー率54% (120/222)
回答No.4

爆熱ペンティアム4搭載のNECデスクトップですね。 2-3年の使用で、劣化が進んでいるものと思われます。 マザーボードのコンデンサなどが心配です。 ケースを開放できるのなら、その状態で、 扇風機で風をしっかり当ててあげれば、応急的には使用できるかもしれません。 コア2デュオなどの最近のPCでは、省電力化・低発熱化が 進んでいますので、これを機に買い替えもひとつの方法でしょう。 インターネット・オフィス程度なら、ネットブック・ネットトップPCがおすすめです。 3-6万円くらいでもメーカーPCが新品でかえますので。

lonpp2
質問者

お礼

回答ありがとうございます。 爆熱なのにケース内、ホコリまみれにしちゃってましたから 余計にまずかったですかね? マザーボード以外なら、なんとかしようと 思ってはいたのですが・・・。 とりあえず前からノートPC欲しかったので、 ゲートウエイのノートを、思い切って買いました。

回答No.3

ソフトウェアが原因で電源が落ちたりモニタの表示がおかしくなるとは考えづらいので、恐らく、GPUやその周りの回路に異常があるものと思われます。 そちらのPCはオンボードグラフィックですので、症状の改善にはマザーボードから交換する必要があります。 電源やメモリの異常なら大体はその箇所の交換ですみますが、メーカー製ということもあるので、保証がまだ効いていれば交換修理等に出すことを強くお勧めします。

lonpp2
質問者

お礼

回答ありがとうございます。 マザーボードかの交換となるとメーカー製ですので やっぱり手に負えないですよね・・。 保証は、症状が出始めた少し前に切れちゃったんです。 見積もり出してみようかなと思いつつも あんま掛かるようだと止めておいた方が良いかな?

回答No.2

考えられるのは、CPUクーラーの故障かも。 >状が出るのは、電源ON後5-20分後ぐらいですが時には、数分で再起動が掛かり、 つい先日、同じような症状が出ました。 色々試したところ、CPUクーラーが動いていないことを確認しました。 社外品に交換したら、直りました。 2005.11 購入ということは、時期的にそろそろ色々故障が発生します。 パソコンも買い替えの時期だと思います。

lonpp2
質問者

お礼

回答ありがとうございます。 CPUクーラーですか・・・。 ケース開けたままの状態で確認してみます。 >2005.11 購入ということは、 >時期的にそろそろ色々故障が発生します。 三年保障付けていたのですが切れて数日で壊れました・・。 >パソコンも買い替えの時期だと思います。 前からノートPC欲しかったので、 安めの(と言っても69800円は、私には大金ですが) ゲートウエイのノートを、思い切って買いました。

noname#214300
noname#214300
回答No.1

PCの年式から考えるに、電源かマザーボードが劣化してきているのではないのでしょうか。 また、CPUが壊れている場合にも同様なエラーが出ることは考えられます。CPUも交換して様子を見られるならば、もう少し原因を絞り込めるとは思いますが。 ちなみに、CPUファンはちゃんと回っているでしょうか。CPUが熱暴走している可能性も考えられます。一度ヒートシンクを取り外し、少しだけグリスを追加してみるのも良いかもしれません。 また、その時CPU近くのマザーボードに取り付けてあるコンデンサがふくれたり液漏れしていないかもチェックしてみることをお勧めいたします。

lonpp2
質問者

お礼

早速の回答、ありがとうございます。 丁寧にお答えいただき、感謝します。 まずは、CPUファンやコンデンサの液漏れ チェックしてみます。

関連するQ&A

  • パソコンの電源が切れない

    パソコンをスタートメニューから終了しようとすると、シャットダウンしていますのメッセージの後に青い画面に英文が出てきてそのまま止まってしまいます。原因は分かる方いるでしょうか?メッセージも載せておくので助けてください。 A problem has been detected and windows has been shutdown to prevent damege to your computer. IQAL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen,restart your computer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed.If this a new installation,ask your hardware or software manu facturer for any windows updates you mighe need. If problems continure,disable or remove any newly installed hardware or software. Disable BIOS memory oputions such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer,press F8 to select Aduanced Statup Options,and then select Safe Mode. Technical infomation STOP:0X0000000A(0X000000B0,0X00000002,0X00000000,0X8052F79E) Beginning dump of physical memory physical memory dump complete. contact your systemad ministrator or technical support group for further assistance.

  • pcの電源をつけたらWindowsが起動する代わりに青いバック画面に白

    pcの電源をつけたらWindowsが起動する代わりに青いバック画面に白い文字の英文が出てきました。対処方法がわからないので英文の訳をお願いいたします。 check to make sure any new hardware or software is properly installed . If this is a new insatllation, ask your hardware or software manufacturer for any windows updates you might need. If preblems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer, press F8 to select Advaced startup options,and then select safe Mode. Technical infomation: stop: 0x0000C1F5 (0x00000000,0x00000000,0x00000000,0x00000000)  長くてすみません。 宜しくお願いいたします。

  • ブルー画面エラー

    このような画面がでてしまいました。 どうすればよいのでしょうか。 よろしくお願いします。 a problem has been detected and windows has been shut down to prevent damage to your computer. page_fault_nonpaged_area if this is the first time you've seen this stop error screen, restart your computer. if this screen appears again, follow these steps: check to make shre any new hardware or software is properly installed. if this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. if problems continue, disable or remove any newly installed hardware or software. disable bios memory options such as caching or shadowing. if you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select safe mode. technical information: stop: 0x00000050 (0xE14D4810,0x00000000,0x8055259a,0x00000001) Beginning dump of physical memory dumping physical memory to disk: 24

  • 「電源を切る」「再起動」時に起きるフリーズの解決方法

    ここ1ヶ月ぐらい前からPCの電源を切るや再起動を実行すると下記のような文字が出でき画面がフリーズします。いつも電源ボタンの数秒押しで強制終了しているのですがこれを解決する方法はありますか? A problem has been detected and windows has been shut down to prevent damage to your computer. IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer.Ifthis screen appears again,follow these steps: Check to make sure any new haedware or software is properly installed. If this is a new installation, ask your hardware or software manugacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restat your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical information: *** STOP: 0X0000000A ( 0X000000B0, 0X00000002, 0X00000000, 0X8052F4DA )

  • ブルースクリーン現象になりました

    質問をさしてもらい ブルースクリーン現象ということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x9589a9b8, 0x00000002, 0x00000000, 0x82ebb60b) *** ntkrnlpa.exe - Address 0x82e4ffd9 base at 0x82e02000 DateStamp 0x4cb710d6 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x00000000, 0x0000001b, 0x00000000, 0x82e95c94) *** ntkrnlpa.exe - Address 0x82e9bfd9 base at 0x82e4e000 DateStamp 0x4cb710d6 三つめ A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe CACHE_MANAGER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information:

  • PCが立ち上がらなくなってしまい、困っています2

    先日ブルースクリーン?で困って質問した者です。 英字の内容を書きます。この場合、直るでしょうか? A problem has been detected and windows has been shut down to provent damage to your computer. UNMOUNTABLE_BOOT_VOLME If this is the first time you've seen this stop errer screen, restart your computer.If this screen appears again,follw these steps:check to make sure any new hardware or software is properly installed. If this is a new installation,ask your hardware or software manufacturer for any windows up dates you might need. If problems continue,disable or remove any newly installed hardware or software.Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer,press F8 to select Adovanced start up options,and ther select safe mode. Technical information:STOP:0x000000ED(0x865C5C08,0x0000006,0x00000000,0x00000000)

  • パソコンが突然エラーが表示され使用できなくなります

    パソコンを使用していると突然画面いっぱいに下記のようなメッセージが出て使用できなくなります。強制終了して再起動し、ウィルススキャンしましたが、ウィルスは検出されてません。半月ほど前に、パソコンが突然シャットダウンしたりして不安定な状態があったのですが、最近は落ち着いていました。 古いパソコンなのでもう寿命でしょうか? 何か、確認方法があれば押して下さい。 パソコン:SONY VAIO PCV-RZ50 表示されたメッセージ A problem has been detected and windows has been shut down to prevent damage to your computer. BAD POOL HEADER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps. Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components,restart your computer,press F8 to select Advanced Startup options,and then select Safe Mode. Technical information; STOP: 0x00000019(0x00000020,0x896784A8,0x89678510,0x0A0D0000) Beginning dump of physical meory physical memory dump complete. Contact your system administrator or technical support group for further assistance.

  • ブルースクリーン

    A problem has been detected and windows has been shut down to prevent damage to your computer. IRQL_NOT_LESS_OR_EQUAL If this the first time you've seen this stop error screen,restart your computer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components,restart your computer,press F8 to select Advaned Startup options,and then select safe Mode. Technical information: *** STOP:0X0000000A(0X00000054,0X00000002,0X00000001,0X804DDC8E) Beginning dump of physical memory physical memory dump complete. contact your system administrator or technical support group for further assistance. 起動したときに上記のように書いてありました。 意味がわかりません・・・

  • PC故障

    PCをきちんと終了しなかったからでしょうか、今朝PCを起動したら、以下のような文面が表示され、どのボタンを押してもWindowsがたちあがらなくなりました。今まではたいがい大丈夫だったんですが、これはやっぱり故障なのでしょうか?(T_T)家電量販店に持って行った方がいいのでしょうか? A problem has been detected and windows has been shut down to prevent damage to your computer. UNMOUNTABLE_BOOT_VOLUME If this is the first time you've seen this stop error screen, restart your computer.If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installtion,ask your hardware or software manufacvrer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software.Disable BIOS memory options such ascaching or shadowing.If you need to use Safe Mode to remove or disable components,restart select safe Mods. Technical information: STOP:0x000000ED (0x86F14900,0xc000009,0x00000000,0x00000000)

  • ブルースクリーンになった

    たびたびブルースクリーンになりますが、 今回は *** STOP: 0x0000001D(0xB64F736A,0xBACD79B4,0x00000000) 前回は A problem has been detected and wiondows has been shut to down to prevent damage to your computer. ORQL-NOT-LESS-OR-EQUAL If this si thefirst time you`ve seen this stop error screen, restart your computer. If this screen again,follow these steps: check to meke sure any new hardware or spftware is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer, press F8 to select advanced startup option, and then select safe mode. Technical information: *** STOP: 0x0000000A (0x00000010,0x00000002,0x00000001,0x8051873C) beginning dump of physical memory physical memory dump complete. Contact your system administrator or technical support group for further assistance. 教えてください、お願いします。