BIOSが壊れた?マザーの電池切れ?教えてください

このQ&Aのポイント
  • BIOSが壊れたのか、マザーボードの電池が切れたのか、起動しなくなってしまった問題について教えてください。
  • 起動時にセーフモードを選ぶ画面が表示され、セーフモードを選んでも繰り返し表示される問題についてどう解決すればいいのでしょうか?
  • ハングアップしてしまう状態で、エラーメッセージが表示される場合、BIOSが壊れた可能性やマザーボードの電池切れが考えられます。どうすれば修復できるのか教えてください。
回答を見る
  • ベストアンサー

BIOS

下記のメッセージが出て起動しなくなってしまいました、症状は セーフモードなどを選ぶ画面が出るのですが、なにを選んでもセーフモードを選ぶ画面を繰り返すだけで、堂々巡りです。 あげくに下記のメッセージでハングアップです。 A problem has been detected and windows has been down to prevent damage to your computer if this the first time you ve seen this stop error screen restat your computer if this screen appears again follow these steps this BIOS in this system is not fully ACPI complianto please contact your system vendor or visit ​http://hardware-update.com​ for an updated BIOS IF youare unable to obtain anupdated BIOS or the latest BIOS supplied by your vendor is not ACPI comoliant you can turn off ACPI mode during text mode setup to do this simply press the F7 key when you are prompted to install storage drivers the system will not notify you that the F7 key was pressed-it will silently disable ACPI and allow you to continue your installation このようなメッセージでハングアップです。 BIOSが壊れたのでしょうか? マザーの電池切れかも? 教えていただきたいのですが、よろしくお願いします。

質問者が選んだベストアンサー

  • ベストアンサー
noname#66624
noname#66624
回答No.1

>BIOSが壊れたのでしょうか? 電源ONしてメーカーロゴ(Windowsロゴではない)出ている間にF2を叩いてBIOSの画面に行き着いて、適当に何か設定が出来ればBIOSは壊れていません。 それから対処手順がありますがご希望に添えるかどうかは分かりません。 参考程度です。 http://dynabook.com/assistpc/faq/pcdata/001681.htm 最初の英文の直訳です。 一部誤字は修正しました。 和訳 問題は見つけられました、そして、こんなに初めてあなたがこの停止エラースクリーンがあなたのコンピュータを再起動するのを見たならば、このスクリーンが再び現れるならば、ウインドウあなたのコンピュータへの損害を防ぐになっていますこれらのステップに従ってください

sherpa4244
質問者

お礼

ありがとうございました、結局F2もなにもダメでした、BIOSが 飛んだんでしょうね! BIOSが起ち上がらない事にはCD起動も出来ないのでリストアも出来ません。 自作機ですので予備のにHD移します、どうもありがとうございました。

その他の回答 (2)

  • violet430
  • ベストアンサー率36% (27472/75001)
回答No.3

直前に設定変更などしていないならハードウェア障害ですね。 修理を依頼した方が良いと思います。

sherpa4244
質問者

お礼

ありがとうございました、BIOSが飛んだんでしょうね! BIOSが起ち上がらない事にはCD起動も出来ないのでリストアも出来ません。 自作機ですので予備のにHD移します、どうもありがとうございました。

  • kani7
  • ベストアンサー率47% (110/231)
回答No.2

ACPIに関するエラーメッセージです。 ACPIは省電力等の電源に関する全般を扱う機能です。 ・Windows側で電源管理に関する設定を変更した ・HALを入れ替えた ・BIOSの電源関係の設定を変更した のいずれかに該当しないでしょうか。

sherpa4244
質問者

お礼

ありがとうございました、BIOSが飛んだんでしょうね! BIOSが起ち上がらない事にはCD起動も出来ないのでリストアも出来ません。 自作機ですので予備のにHD移します、どうもありがとうございました。

関連するQ&A

  • ウインドウズが起動しない

    下記のメッセージが出て起動しなくなってしまいました、症状は セーフモードなどを選ぶ画面が出るのですが、なにを選んでもセーフモードを選ぶ画面を繰り返すだけで、堂々巡りです。 あげくに下記のメッセージでハングアップです。 A problem has been detected and windows has been down to prevent damage to your computer if this the first time you ve seen this stop error screen restat your computer if this screen appears again follow these steps this BIOS in this system is not fully ACPI complianto please contact your system vendor or visit http://hardware-update.com for an updated BIOS IF youare unable to obtain anupdated BIOS or the latest BIOS supplied by your vendor is not ACPI comoliant you can turn off ACPI mode during text mode setup to do this simply press the F7 key when you are prompted to install storage drivers the system will not notify you that the F7 key was pressed-it will silently disable ACPI and allow you to continue your installation このようなメッセージでハングアップです。 BIOSが壊れたのでしょうか? マザーの電池切れかも? 教えていただきたいのですが、よろしくお願いします。

  • stopエラー 0x000000A5  が出ます!

    知人に質問されたのですがあいまいな答えしか出ないため みなさんのお力をお借りしたく質問いたします。 状況を見たわけではないのではっきりしていませんが、よろしくお願いいたします。 【経緯】 HD故障により、起動しなくなったPCのHDを入れ替えて新規にリカバリーディスクによりウィンドウズXPの再インストールを行い、起動しようとしていますが下記のエラーメッセージによりインストールができません。 【OSインストール時のエラーメッセージ】 A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you’ve seen this stop error screen. Restart your computer. If this screen appears again. Follow these steps: The BIOS in this system is not fully ACPI complaint. Please contact your system vendor or visit http://www.hardeare-update.com for an updated BIOS. If you are unable to obtain an updated BIOS or the latest BIOS supplied by your vendor is not ACPI compliant, you can turn off ACPI mode during text mode setup. To do this, simply press the F7 key when you are prompted to install storage drivers. The system will not notify you that the F7 key was pressed – it will silently disable ACPI and aloe you to continue your installation. Technical information: *** stop: 0x000000A5 ( 0x00000011 , 0x00000007 , 0xF89FD0C0 , 0x0100000E ) 【パソコンの情報】 J2705 emachines

  • 起動画面エラーについて

    コンピューター起動時に、バックが青の画面で a problem has been detected and windows has been shut down to prevent damage to you computer if this is the computer.if this screen appears again,follow these steps: the bios in this system is not fully acpi compliane. please contact your system vendor for an updated bios. techinical information; の画面が出ます。これは、BIOSが壊れているのでしょうか?

  • ウインドウズが立ち上がりません

    先日、過って違うタイプのメモリーを増設しようとして、電源が入らず (入るが、ピーピーという音が断続的に鳴り続ける)、再起動もできないので 電源スイッチでオンオフを繰り返していたら、元のメモリーだけでも ウインドウズが立ち上がらなくなってしまいました。画面にはこんな表示が出ます。 A plobrem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen,restart your computer. If this screen appears again,follow these steps: The BIOS in this system is not fully ACPI compliant. Please contact your system vendor or visit http://www.hardware-update.com for an update BIOS. If you are unble to obation an update BIOS on the latest BIOS supplied by your vendor is not ACPI compliant,you can turn off ACPI mode durning text install storage drivers. The system will not notify you that the F7 key was pressed-it will silently distable ACPI and allow you to continue your installation. Technical information : ☆☆☆(←☆に近い記号です)Step:0X000000A5 (0X00010007,0X000000FD,0X00000000,0X00000000) 以上です。これはどのような部分が壊れ、どう対処すればよいでしょうか?ウインドウズのCD-ROMはありますが、再インストールのような形になって、Cドライブのファイルが消えてしまうことはなるべく避けたいです。セーフモードでも立ち上がりませんでした。 おわかりになる方、アドバイスをよろしくお願い致します。

  • 急にACPIのエラーメッセージがでるようになってしまいました

    設定を変えていないのに、起動中にブルー画面になって以下のメッセージがでるようになってしまいました。 再インストールすれば、直るとは思うんですが、再インストールなしで起動するようにする方法はありませんか? *** STOP: 0x000000A5 (0x00000001,0x8207F4C8,0x00000000,0x00000000) The ACPI BIOS in this system is not fully compliant with the ACPI specification.Please read the README.TXT for possible workarounds. You can also contact your system's manufacturer for an updated BIOS, or visit http://www.hardware-update.com to see if a new BIOS is available. The BIOS in this system is not fully ACPI compliant. Please contact your system vendor or visit http://hardware-update.com for an updated BIOS.If you areunable to obtain an updated BIOS or the latest BIOS supplied by your vendor is not ACPI conpliant,you canturn off ACPI mode during text mode setup. To do this,simply press the F7 key when you are prompted to install storage drivers. The system will not nofify you that the F7 key was pressed - it will silently disable ACPI and allow you to continue your installation.

  • ACPIのシステムエラーがでます

    DOS/V初心者です。 数日前、ABITのマザーボードBD72(845Eチップ)を組みましたが、数時間使うといきなり落ちて次のようなエラーがでます。 A problem has been detected and windows has been shut doun to prevent damage to your computer. If this is the first time youre seen this stop error screen,restart your computer. If this screen appears again,follow these steps. The BIOS in this system is not fully ACPI compliant. please contact your system vendor or visit http://www.hardware-update.com for an updated BIOS. If you are unble to obtain an updated BIOS or the latest BIOS supplied by your vendor is not ACPI conpliant, you can turn off ACPI mode during text mode setup. TO do this,simply press the F7 key when you are prompted to install storage drivers. The system will not notify you that the F7 key was pressed it will silently disable ACPI and allow you to continue your installation. Technical in formation: ***stop:0X000000A5(0X00000011,0X00000007,0XF7AC60C0,0X0100000C) 私、語学は中一レベル。どうしたらいいんでしょう? BIOSはアワード・OSは98SEをクリーンインストールして即XPホームにUPしました。メモリー512M(PC2700)+512M(PC2100)2本差し。(あまりよくないと思いますが、1Gで認識してます)CPU2.0AGHz。電源SWを切り、投入するとXPの起動方法選択画面になりますので、その度に通常起動で使ってます。

  • グラボ交換後にエラー

    こんにちわ、よろしくお願いします。 今まで使っていたグラボ(GeForce8500GT)が壊れてしまいモニターが真っ黒な状態になってしまった為新しくショップの人に8500GTと同じ位の性能だといわれてGeForce210というものを購入して交換し、PCを起動したところWindowsのロゴの画面になったとたんブルースクリーンが出てしまい起動できなくなってしまいました。 ブルースクリーンには A problem has been detected and windows has been shut down to prevent damage to your computer If this is the first time you've seen this stop error screen, restart your computer.If this screen appears again,follow these steps: The BIOS in this system is not fully ACPI compliant.please contact your system vendor or visit http://www.hardware-update.com for an updated BIOS. If you are unable to obtain an updated BIOS or the latest BIOS supplied by yourvendor is not ACPI compliant,you can turn off ACPI mode during text mode setup.To do this,simply press the F7 key when you are prompted to install storage drivers.The system will not notify you that the F7 key was pressed-it will silently disable ACPI and allow yor to continue your installation. Technical information: という文章と STOP:0x000000A5(0x00000002,0x8A337410,0xE1506228,0x8A355030) と書いていました。 何か解決策をご存知の方いらっしゃいましたらよろしくお願いします。

  • 起動しなくなってしまいました。

    自作PCに、OSは2000を使用してます。 今まで何の問題もなく起動してましたが、いきなりPCが再起動しました。その後BIOS画面が出て通常通り2000の起動画面が出るのですが、その途中再度再起動し、下の文字が表示されます。それからは一切動きません。なぜこのような現象になったのか不思議です。元に戻るのでしょうか? すみません、どなたかアドバイスよろしくお願いします。 *** STOP: 0x000000A5 (0x00000011,0x00000001,0x00000000,0x00000000) The ACPI BIOS in this system is not fully compliant with the ACPI specification.Please read the README.TXT for possible workarounds. You can also contact your system's manufacturer for an updated BIOS, or visit http://www.hardware-update.com to see if a new BIOS is available. The BIOS in this system is not fully ACPI compliant. Please contact your system vendor or visit http://www.hardware-update.com for an updated BIOS. If you are unable to obtain an updated BIOS or the latest BIOS supplied by your vendor is not ACPI compliant,you can turn off ACPI mode during text mode setup. To do this,simply press the F7 key when you are prompted to was pressed - it will silently disable ACPI and allow you to continue your installation.

  • 98から2000へインストールできません

    現在、古いパソコンを使っている素人です。Windows98から2000へクリーンインストールしようとインターネットなどで仕方を調べつつ取りかかっていました。4枚の起動ディスクを作成し、フロッピー4枚目の時に突然、青の画面に「The BIOS in this system is not fully ACPI compliant. Please contact your system vendor or visit http://www.hardware-update.com. for an updated BIOS. If you are unable to obtain an updated BIOS or the latest BIOS supplied by your vendor is not ACPI compliant , you can turn off ACPI mode during text mode setup. To do this , simply press the F7 key when you are prompted to install storage drivers. The system will not notify you that the F7 key was pressed - it will silently disable ACPI and allow you to continue your installation.」という文面が現れ、それ以降操作できない状態となっております。どうすれば、きちんとインストールできるのでしょうか?使用しているパソコンはサンヨーのB5ノートパソコンでMBC-G1Vです。アドバイスお願いします。

  • エラーメッセージ

    ちょっと長くなりますがエラーメッセージを書くので対処方法を教えてください。 A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these stops. Check to be sure you have adequate disc space. If a drive is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any Bios updates. disable BIOS memory options such as caching or shadowing. if you need to uses safe Mode to remove or disable components, restart your computer, prees F8 to select Advanced startup options, and the select safe mode. このメッセージが出て勝手にwindowsが再起動します。 何が原因でしょうか?