• 締切済み

American Megatrends現れ動かない

American Megatrendsという画面が現れて、動きません。 書いてある内容が何を意味して、どうすればいいか分かる方、教えてください。 以下にそのメッセージを書いておきます。お願い致します。 Pres F12 for BBS POPUP F2 for sentup utility The MCH is operating with DDR2 800 DRAM Timing :Tcl :6/Tras:18/Trp:6/Trcd:6/Twr:6/Trfc:52/Twtr:3/Trrd:3/Trtp:3/ Initializing USB controllers..Dome.. 2014MB OK USB Device(s):1 Mouse Auto-Detecting AHCI PORT0.. Hard Disk Auto-Detecting AHCI PORT1.. ATAPI CDROM SATA Port0 ST3320418AS CC45 S.M.A.R.T capable and status OK SaTA Port1 Optiarc DVD +/-RW AD-7230S 102B Auto-detecting USB Mass Storage Devices 00 USB mass storage devices found and configured. Strike the F1 key to continue. F2 to run the utility. 以上の様に出ております。  

みんなの回答

  • MNH10W
  • ベストアンサー率48% (2859/5927)
回答No.3

ANo.2 です 起動順序に問題がなければ、HDDにエラーがあり起動できない状況です BIOS設定画面で起動順序を確認してHDDが1番になっていればHDD交換でリカバリですね。

aobe1979
質問者

お礼

ご回答ありがとうございました。

  • MNH10W
  • ベストアンサー率48% (2859/5927)
回答No.2

「CMOS Settings Wrong」とか「CMOS Date/time Not Set」等が表示されるのなら、BIOS設定保持用電池の消耗です >00 USB mass storage devices found and configured. カードリーダーにメディア(SDカード等)が入れっぱなしとか。

aobe1979
質問者

お礼

回答ありがとうございました。 また、新たな画面が出てしまい、困っております。 お力をいただけませんでしょうか。

aobe1979
質問者

補足

回答ありがとうございます。 イヤフォンもさしっぱなしでしたが、そういうのも原因でしょうか。 BIOS設定保持用電池の交換は、業者でなければだめでしょうか。 さきほど、もう一回答頂いた方のF1を押したのですが、 また、新たなメセージが出てしまいました。 お分かりになれば、教えていただきたいです。 宜しくお願い致します。 F1を押したところ、画面が青い色になり又、メッセージが出ています。 A problem has been detected and windoes has been shut down to prevevt damage to your computer. UNMMOUNTABLE_BOOT_VOLUME If this is the first time youve seen this stop error screen. restrt your computer.If this screen appears again. follow these steps: chek to make sare any new hardware or software is properly installed. If this is a new installation.ask your hardware or software manufa cture for any windows updates your might need. If problems continue.disable.or.remove any nealy installed hardware of sofutware. Disable.Blos memory options such as caching or shadming. If you need to use safe mode to more or disable componets.restart your conputer.press F8 to select Advanced startup options.and then Select safe Mode. Te chnical information: STOP :0x000000ED (0x89D93e30.0xcoooooo6.0x00000000.0x0000000000)

回答No.1

F1を押せば進みます。 F2を押すとBIOSメニューに入ります。 BIOSが初期化された場合に出るメッセージです。

aobe1979
質問者

お礼

回答ありがとうございました。 F1をおしたら、また新たなメッセージが出てきてしまいました。 お力をかして頂けたら、幸いでございます。

aobe1979
質問者

補足

回答ありがとうございます。お聞きしてよろしいでしょうか。 F1を押したところ、画面が青い色になり又、メッセージが出ています。 A problem has been detected and windoes has been shut down to prevevt damage to your computer. UNMMOUNTABLE_BOOT_VOLUME If this is the first time youve seen this stop error screen. restrt your computer.If this screen appears again. follow these steps: chek to make sare any new hardware or software is properly installed. If this is a new installation.ask your hardware or software manufa cture for any windows updates your might need. If problems continue.disable.or.remove any nealy installed hardware of sofutware. Disable.Blos memory options such as caching or shadming. If you need to use safe mode to more or disable componets.restart your conputer.press F8 to select Advanced startup options.and then Select safe Mode. Te chnical information: STOP :0x000000ED (0x89D93e30.0xcoooooo6.0x00000000.0x0000000000) 以上のメッセージが出ているのですが、 この後に、F2を押せばよろしいのでしょうか? お願い致します。

関連するQ&A

  • american megatrendsが出ています

    american megatrendsという表示が出て、そのあと動かなくなりました。 表示の意味を調べたのですが、badの部分の意味が分からないため質問させていただきました。 この後に、どうすればいいのか教えてください。お願いいたします。 press F12 to boot on Network The MCH is operating with DDR3 800 DRAM Timing : Tcl6 / Tras:15 / Trp:6 / Trcd:6 / Twt:6 / Trfc:44 / Twtr:4 / Trrd:3 /Trtp:4 Initializing USB controllers..Done. 990MB OK USB Device(s):1 Mouse Auto-Detecting AHCI PORT 0 .. IDE Hard Disk Auto-Detecting AHCI PORT 1 ..ATAPI CDROM SATA PORT 0 ST380815AS 3.AAC S.M.A.R.T Capable and Status OK SATA PORT 1 HL-PT-STDVD-ROM GDRH20N 0P04 Auto-detecting USB Mass Storage Devices... 00 USB mass storage devices found and configured. CMOS Checksum Bad. Press F2 to Enter Blos setup 以上になります。どうか、よろしくお願いいたします。

  • PC起動時American Megatrendsが

    PCを立ち上げると、American Megatrends と表示されます。 他にもこの表示がされている方がたくさんいるのですが、同じ内容のものが 見つかりませんでした。 私の場合は何が原因なのでしょうか? よろしくお願いします。 Press F2 for BBS POPUP F2 for setup utility The MCH is operating with DDR2,800 DRAM Timing : Tcl:6/Tras:18/Trp:6/Trcd:6/Twr:6/Trfc:52/Twtr:3/Trrd:3/Trtp:3 Initializing USB conttollerds...Done 2014MB OK USB Device(s):1 Keyboard,1 Mouse Auto-Detecting AHCI PORT 0..HardDisk Auto-Detecting AHCI PORT 1..ATAPI CDROM SATA Port 0 SAMSUNG HD322HJ 1ACO1113 S.M.A.R.T. Capable and Status OK SATA Port 1 PLDS DVD+/-RW DH-16A65 YD11 Auto-detecting USB Mass Storage Devices.. 00 USB Mass storage devices found and configured SYS fan failure Strike the F1 key to continue F2 to run the setup utility 上記のように表示され、毎回F1でWindowsに戻っています。

  • American Megatrendsについて

    PC起動時に毎回American Megatrendsが表示されます。 内容は下記のとおりです。 Speed : 2.66 GHz Press F2 key to enter setup Menu, Press F3 if you want to boot from the network F12 to enter Boot Menu The IMC is operating with DDR3 1333MHz, 9 CAS Latency DRAM Timings: Tras:24/Trp:9/Trcd:9/Twr:10/Trfc:74/Twtr:5/Trrd:4/Trtp:5/Tfaw:20 2040MB OK USB Device(s):1 keyboard, 1 Mouse, 2 Hubs Auto-Detecting AHCI PORT 0..SATA Hard Disk Auto-Detecting AHCI PORT 2..ATAPI CDROM SATA Port1 WDC WD3200AAKS-75L9A0 02.03E02 SATA Port3 PLDS DVDRW/BDROM DH-6E2S AD16 Auto-detecting USB Mass Storage Device .. 00 USB mass storage devices found and configured. Alert! Memory size is decreased . F1 to Resume, F2 to setup 他の質問者様の内容を見てみたり、翻訳をしてみて主訴を探ろうと頑張ってみたのですが あまり良くわからず対処できていないのが現状です。 よろしければ原因や対処法など教えていただければと考えております。 よろしくお願いします。

  • パソコンのエラー?

    パソコン起動時に以下のメッセージが出てくるのですが、内容がよくわからず困っています。その画面のときF1キーを押すと正常に立ち上がり普段どおり動作するのですが...どなたか解る方いらっしゃいますか? メッセージは Available The MCH is operating with DDR2 800 DRAM Timing:Tcl:6/Tras:18/Trp:6Trcd:6/Twr:6/Trfc:42/Twtr:3/Trrd:3/Trtp:3 Initializing USB Controllers.. Done. 990MB OK USB Device(s):1 Keyboard 1 Mouse Auto-Detecting AHCI PORT 0 .. Hard Disk Auto-Detecting AHCI PORT 1 .. ATAPI CDROM SATA Port 0 SAMSUNG HD083GJ 1AC01113 S.M.A.R.T capable and Status OK SATA Port 1 PBDS CD-RW/DVD-ROM DH-48C2S ND12 Auto-Detecting USB Mass Storage Devices.. 00 USB mass storage devices found and configured. CMOS checksum error Strike the F1 key to continue, F2 to run the setup utility 以上になります。どなたか解る方がいらっしゃいましたら、是非とも宜しくお願いいたします。

  • (DELL)American Megatrendsと立ち上げ後表示され

    (DELL)American Megatrendsと立ち上げ後表示される。 「American Megatrends」以下に表示される文字です。 speed:2.80GHz Press F2 key to enter setup menu, press F3 if you want to boot from the network F12 to enter boot Menu The IMC is operating with DDR3 0333MHz, 9 CAS Latency DRAM Timings:Tras:24/Trp:9/Trcd:9/Twr:10/Trfc:74/Twtr:5/Teed:4/Trtp:5/Tfaw:20 Initializing USB Controllers..Donw. 4088MB OK USB Device(s):2 Hubs Auto-Detecting AHCI PORT 0..SATA Hard Disk Auto-Detecting AHCI PORT 2..ATAPI CDROM ASTA Port1 WDC WD1600AAJS-75M0A0 02.03E02 SATA Port3 TSSTcorp DVD+/-RW TS-H653G DW10 Auto-detecting USB Mass Storage Devices.. 00 USB mass storage device found and configured. Keyboard not found F1 to Resume,F2 to Setup 以上 まだ購入1年、保証期間が過ぎて1週間程です。苦笑 出来れば修理でなく自分で解決したいと思っています。 ・これはどういった症状なのでしょうか。 ・自分でリカバリーしようにも英語表記なので不安です。  言語を日本語に変えることはできないでしょうか ・DELLボストロ430です ご回答よろしくお願いします

  • AmericanMegatrendsで質問です。

    デルのデスクトップパソコンが 起動しなくて困っております。 起動すると・・・ Press F2 to run Seup Press F12 for BBS POPUP Enable/Disable Onboard PCIE Metwork Controrrer. Initializing USB Controrrers .. Done. 6136MB OK USB Device[c]: 1 Keyboard Auto-Detecting AHCI PORT 0..ATAPI CDROM Auto-Detecting AHCI PORT 2..IDE Hard Disk SATA Port0 PLDS DVD+/-RW DH-16ABS PD11 SATA Port2 HitachiHDS721010CLA332 JP403FF S.M.A.R.T. Capable and Status BAD Auto-detecting USB Mass Storage Devices.. 00 USB mass storage devices found and configured. AHCI Port2 Device Error Press F1 to Resume と画面表示されてしまいます。 どのように対応すればよろしいのでしょうか? お分かりになる方がいましたら ご指導下さい。 よろしくお願いします。

  • American Megatrendsで困ってます

    買ったばかりのFLONTIERのデスクトップですが 今日電源を付けるとAmerican Megatrends と出ました;;; 内容は press del to run setup press f11 for bbs popup press f12for pxe installed memory:8192 mb/pc1600-dual channel initializing usb controllers... devices total: 1 kbds, 2 hubs, 0 mice, 0 mass done. auto-detecting usb mass storage devices.. 00 usb mass storage debices found and configured sata port0: not installed sata port1: not installed sata port2: ST500DM002-1BD142 ultra DMA Mode-5, S.M.A.R.T Capable and Status ok sata.port3: ATAPI DVD A DH24ACSH NO Mouse Detected! Press F1 to Resume です。検索したところF1でとりあえずウインドウズの画面に 行くことは分かったのですが、エラーメッセージが違ったようなので 質問させていただきました。 回答よろしくお願いします;; この手には初心者なので助けてください;

  • パソコンが起動しません。助けて下さい!

    パソコンの電源を入れたら、American Megatrendsとロゴの入ったページが表示され、パソコンが使えません。キーボードも何も反応しません。誰か助けて下さい。よろしくお願いします。 表示されている文章は以下の通りです。 Press F12 for BBS POPUP F2 for setup utility The MCH is operating with DDR2 800 DRAM Timing: Tcl:6/Tras:18/Trp:6/Trcd:6/Twr:6/Trfc:52/Tutr Initializing USB Controllers .. Done. 3038MB OK Auto-Detecting AHCI PORT 0..Hard Disk Auto-Detecting AHCI PORT 1..ATAPI CDROM SATA Port0 WDC WD3200AAKS-75L9A0 01.03E01 S.M.A.R.T. Capable and Status OK SATA Port1 HL-DT-ST DUDRAM GSA-4120B A112 Auto-detecting USB Mass Storage Devices .. Device #01 : I-0 HDCR-U *HiSpeed* 01 USB mass storage devices found and configured Keyboard failure Strike the F1 key to continue, F2 to run the setup utility 以上です。 誤字脱字等ありましたら申し訳ありません。 どうかよろしくお願いします。

  • American Megatrendsと出てしまう

    American Megatrendsと出て止まってしまいます。 Press DEL to run Setup Press ESC for BBS POPUP 1 AMD North Bridge, Rev G2 Initializing USB Controllers .. Done. 2048MB OK USB Devoce(S):1 Keyboard,1 Hub Auto-Detecting Pri Master..Hard Disk Auto-Detecting Pri Slave...ATAPI CDROM Pri Master : ST3250820NS 3.AEG Ultra DMA Mode-6,S.M.A.R.T.Capable and Status OK Pri Slave : HL-DT-ST DVDRAM GH22NS50 JN00 Ultra DMA Mode-5 Auto-detecting USB Mass Storage Devices.. 00 USB mass storage devices found and configured. Mouse not found Please Press 'F1'key skip warning message,or 'Del' Key enter Setup! と書かれています。 フリーズして動かなくなったので強制終了してからこの様な症状になってしまいました。 F1押してもOS画面にいかず真暗になります。

  • 自作のpcをゆずってもらい立ち上げてみると

    自作のpcをゆずってもらい立ち上げてみると American Megatrends press ESC for BBS popup DRAM  Timing:TCL:5/Tras:16/Trp:5/Trcd:5/Tur:6/Trfc:52/Tutr:3/Trrd:3/Trtp:3 Dual Channel Initializing USB Controllers ..Done. 4096MB Ok USB Device(s):1 Keyboard,4 Storage Devices Auto-Detecting Pri Master..IDE Hard Disk Auto-Detecting Sec Slave...ATAPI CDROM Pri Master:ST3500320AS SD15        s.M.A.R.T.Capable and Status OK Sec Slave:HL-DT-ST BD-RE GGV-H20N XL03 Auto-detecting USB Mass Storage Devices.. Device #01:MITSUMI---  Device #02:MITSUMI---  Device #03:MITSUMI---  Device #04:MITSUMI--- 04 USB mass Storage devices found and configured. Mouse not found please press‘F1’key skip warning message,or ‘Del’key enter setup! と出ます 何のことやらさっぱり解りませんがF1を押すと普通に立ち上がりましたが 立ち上げるたびに また同じ画面になります どうしたらよいのでしょうか? どなたか教えてください