• 締切済み

起動できなくなりました。(fedora core1)

以前作った練習用Linux(fedora core1)機をを久々に起動させると、途中で止まり、進まなくなりました。 Kernel panic : No init found. Try passing init=option to kernel. 分かるか違いましたら是非教えて下さい。 ネットでも同じようなエラー?はあるようなのですが、解決法がありませんでしたので。 何が必要か分かりませんので、分かる範囲で書いてみました。 必要な情報がありましたら書きますので教えて下さい。 <エラーと思われる画面抜粋> (省略) Creating root device hda : dma_intr : status=0x51 { DriveReady SeekComplete Error} hda: dma_intr : error=0x40 { UncorrectableError },LBAsect1349460,sector=0 end_request: I/O error,dev 03:03 (hda), sector 0 (上記3行同文にて省略) mkrootdev: label / not found Mounting root filesystem mount : error 2 mounting ext3 pivotroot : pivot_root(/sysroot,/sysroot/initrd) failed : 2 umount /initrd/proc failed:2 Freeing unused kernel memory : 136k freed Kernel : No init found. Try passing init=option to kernel. ---------------------------- GRUB ver.0.93 使用 デスクトップ機を使用。OSはfedora core1のみインストール。 インストール後ブートディスクは作成済み。 (ブートディスクを挿入し起動のみでは同様のエラー) USB機器は使用していない。 CUIでの使用のため、PS/2キーボードとモニタケーブルを接続するのみ。 前回使ったときは覚えていないが、設定の変更はしていない。 ・ファイルサーバとして使用していたこともあり、データが消えてしまう再インストールはしたくありません。 ・データを残せる、再インストールなどがありましたらすることは可能です。 (各種設定はします。) おわかりの方がいましたらよろしくお願い致します。

  • a-k-a
  • お礼率43% (77/176)

みんなの回答

  • xjd
  • ベストアンサー率63% (1021/1612)
回答No.2

>hda : dma_intr : status=0x51 { DriveReady SeekComplete Error} >hda: dma_intr : error=0x40 { UncorrectableError },LBAsect1349460,sector=0 >end_request: I/O error,dev 03:03 (hda), sector 0 ディスクのハード(?)エラーがでてますね。 まずは、 ファイルシステムの修復 不良セクタの退避 を試してみてください。 CDROMからレスキューモードで起動する。 (ディスクのルートファイルシステムはマウントしない) fsck または e2fcsk で全てのファイルシステムを修復してみる。 e2fsck -c で不良セクタを退避する。 ディスクのハード障害であれば、早めに交換することをお勧めします。

a-k-a
質問者

補足

ハードのほうですか・・・ 専用の機械でほとんど使っていないのでそれはないだろうって思ってたんですが(というより考えたくなかったf^^;) 本の付録CDROMなんですがレスキューモードで起動できるのでしょうか? FDのブートディスクとCDROMで「linux rescue」でしたのですが、同じ箇所でとまってしまいました。 (マウントしてるってことですよね?) 手順の載っているサイト等ご存知でしたら教えていただけないでしょうか? うまく検索できなかったので。。。

  • estea
  • ベストアンサー率44% (39/87)
回答No.1

ディスクに問題が生じてるんでしょうかねぇ。 俺が同じ状況になったら、別のマシンか新しいHDDにLinuxやwindowsいれてそこにぶら下げるかな。 新しく用意したOSからデータだけ引き抜くかな。できるかわからんけど試しては見る。 レスキューディスクやCDブートで起動できればまだ手はあるんだろうけどねぇ。

a-k-a
質問者

補足

FDのブートディスクと本についていたCDROMはあるんですが、手はあるでしょうか? とりあえず挿入して入力画面に「linux rescue」とやっただけでは同じような箇所でエラーになってしまいました。

関連するQ&A

  • カーネルをアップデートしたら起動しなくなった

    Redhat 9.0 2.4.20-31.smpから2.6.9にアップデートして再起動したら起動しなくなりました。 再起動で止まってしまった最後の数行を下に書きます。 正常に起動できる方法はあるでしょうか。 よろしくお願いします。 Mounting /proc filesystem Creating block devices Creating root device Mounting root filesystem mount: error 19 mounting ext2 pivotroot: pivot_root(/sysroot,/sysroot/initrd) failed:2 umount /initrd/proc failed: 2 Freeing unused kernel memory: 232k freed Kernel panic - not syncing: No init found. Try passing init=option to kernel

  • LINUXで起動できなくなりました。

    家庭用ファイル(Samba)サーバとして利用していたマシンがカーネルパニックで起動できなくなってしまいました。 2週間ほど自宅を留守にし、帰宅後起動したら起動できませんでした。 特に設定も変更していませんし、アップデートもしていませんので単純にHDD(IDE)の故障(?)だと思われます。 HDD中(homeディレクトリ)のデータを救いたいのですが、なにか方法がありますでしょうか。起動中に下記エラーが出て固まってしまいます。 KNOPPIXでCDから起動しましたが、別のエラーが出て固まってしまいます。 どなたか助けていただけませんでしょうか。。。 よろしくお願いいたします。 デストリビューション White Box Enterprise Linux 2.4.21-27.0.2.EL end_request: I/O error,dev 03:00 (hda), sector 24772228 hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=24772230, high=1, low= 7995014, sector=24772230 end_request: I/O error,dev 03:00 (hda), sector 24772230 > ide-floppy driver 0.99.newide md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Initializing IPsec netlink socket NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configurate (established 16384 bind 32768) Linux IP multicast router 0.06 plus PIM-SM Initializing IPsec netlink socket NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 164k freed VFS: Mounted root (ext2 filesystem). Red Hat nash version 3.5.13 starting Loading jbd.o module Journalled Block Device driver loaded Loading ext3.o module Mounting /proc filesystem Creating block devices Creating root device mkrootdev: label / not found Mounting root filesystem mount: error 2 mounting ext3 pivotroot: pivot_root(/sysroot,/sysroot/initrd) failed: 2 umount /initrd/proc failed: 2 Freeing unused kernel memory:152k freed Kernel panic: No init found. Try passing init= option to kernel.

  • カーネルの再構築について

    現在、カーネルの再構築を行っているのですが、設定後bootすると必ずkarnelpanicを起こしてしまいます。 boot時のエラーメッセージは mounting root filesystem mount: error 19 mounting ext3 pivotroot: pivot_root(/sysroot,/sysroot/initrd) failed: 2 Freeing unused kernel memory: 240k freed Kernel panic: No init found. Try passing init= option to kernel. で何らかの理由でファイルシステムのマウントが失敗してしまっているようなのですが、回復法が見つからないので教えてください。 現在使用しているkarnelは2.4.20で再構築で切り替えようとしたのは2.4.31と2.6.11の2つでどちらも同じエラーでした。よろしくお願いします。  osはredhat9です。

  • TM5800にRedHat9

    TM5800搭載のマザーボードにRedHat9をインストールしようとしています。 OSのインストールは成功するのですが、GRUB画面でOSを選択した後、 起動時にブートセクタあたりのリードに失敗しているらしく、起動が出来ません。 (画面が流れてしまい、表示が読みとれないのですがDMAのエラーが多数でます) 確認のできたエラーの内容は以下です。 mount: error 2 mounting ext3 pivotroot: pivot_root(/sysroot,/sysroot/initrd)failed:2 umount /initrd/proc failed :2 Freeing unused kernel memory: 116k freed Kernel panic: No init found. Try passing init= option to kernel. HDDは、以下の2点で確認してみました。 ・TOSHIBA MK4025GAS ・IBM   DARA-212000 BIOSの設定が間違っているのでしょうか? 何か分かる方がいたら教えてください。

  • Redhat Linux Kernel Panicについての質問です。

    Redhat Linux Kernel Panicについての質問です。 急にサーバへの疎通がとれなくなり 原因がわからぬまま、再起動されていました。 再起動時に以下の画面でずっととまったまま何もキーがききません。 外部起動Diskがないため、どうしたらよいかもわかりません。 再インストールしかないのでしょうか。 どうにか復旧したいのですが、いろいろ調べましたが、 必ず起動Diskの話がでてきてしまいます。 以下、起動時に最後に表示された部分です。 Partition check: sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > Loding jdb.o module Journalled Block Device driver loaded Loding ext3.o module Mounting /proc filesystem Creating block devices Creating root device Mounting root filesystem Kjournald starting. Commit interval 5 seconds EXT3-fs : mounted filesystem with ordered data mode. pivotroot: pivot_root(/sysroot,/sysroot/initrd) failed:2 umount /initrd/proc failed:2 freeing unused kernel memory: 164k freed Kernel panic: No init found. Try passing init= option to kernel.

  • grubでkernel panic

    DELLノートにXPとVine2.6のデュアルブートをしたいのですが,grubでLinuxを起動できません. インストールではliloをMBRではなくBOOTに書き込んでいます. つまり,先にXPを起動できるようにしてから次にgrubでLinuxを起動させる手順を選択しております. デュアルブートの解決方法などを教えていただけませんでしょうか? …以下、症状です… 僕は hda1: DELL hda2: NTFS hda3: ext3 hda4: extenstion hda5: ext3 hda6: swap でhda3にBOOT,hda5に本体を置いてるので  grub> root (hd0,2)  grub> kernel /vmlinuz root=/dev/hda3  grub> boot だけだと kernel panic: no init found Try passing it=option to kernel と怒られますので bootの直前に  grub> root (hd0,4)  grub> initrd /initrd/initrd.img としようとするのですが、initrd.imgがありません.  grub> root (hd0,2) と打つと Filesystem type is ext2fs, partision type 0x83 と帰ってきますが,   ^ ext3fsでないのが気になります. 再インストールしてliloをMBRに書き込んでから 先にLinuxを起動できるようにして, 次にgrubでXPを起動させる方が簡単でしょうか?

  • ハードディスクの故障? DriveReady SeekComplete Error

    VineLinuxを使用しているのですが、エラーが発生するようになりました。 メッセージを見る限り、ハードディスクの故障のように思えるのですが、Linux自体は問題なく使えます。 試しに、コンソールから「shutdown -r -F now」を実行し、リブートとディスクのチェックを行ってみました。 リブート時にエラーは出力されないのですが、しばらく使っているとまた同じエラーメッセージが出力されました。 物理的にハードディスクが故障しているのであれば、 交換を考えています。 このエラーの意味がわかる方、あるいは同じ現象になった方が いましたら、アドバイスを頂けないでしょうか? 【以下エラーメッセージの抜粋】 Apr 6 04:12:48 localhost kernel: hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } Apr 6 04:12:48 localhost kernel: hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=11661780, sector=11661773 Apr 6 04:12:48 localhost kernel: ide: failed opcode was: unknown Apr 6 04:12:48 localhost kernel: end_request: I/O error, dev hda, sector 11661773 Apr 6 04:12:53 localhost kernel: hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } Apr 6 04:12:53 localhost kernel: hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=11661780, sector=11661773 Apr 6 04:12:53 localhost kernel: ide: failed opcode was: unknown Apr 6 04:12:53 localhost kernel: end_request: I/O error, dev hda, sector 11661773 Apr 6 04:12:57 localhost kernel: hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } Apr 6 04:12:57 localhost kernel: hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=11661780, sector=11661773 Apr 6 04:12:57 localhost kernel: ide: failed opcode was: unknown Apr 6 04:12:57 localhost kernel: end_request: I/O error, dev hda, sector 11661773 Apr 6 04:13:01 localhost kernel: hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } Apr 6 04:13:02 localhost kernel: hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=11661780, sector=11661773 Apr 6 04:13:08 localhost kernel: ide: failed opcode was: unknown Apr 6 04:13:08 localhost kernel: end_request: I/O error, dev hda, sector 11661773 Apr 6 04:13:08 localhost kernel: hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } Apr 6 04:13:08 localhost kernel: hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=11661780, sector=11661773 Apr 6 04:13:08 localhost kernel: ide: failed opcode was: unknown Apr 6 04:13:08 localhost kernel: end_request: I/O error, dev hda, sector 11661773

  • HDDの故障の前兆?

    Linuxを起動する時のBOOT画面で、 hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { BadCRC DriveStatusError }, LBAsect=1516476, sector=1146980          :          : と表示されてしまします。 スーパーユーザーで #fsck と実行しても解決されませんでした。 これは、HDDが危険な状況にあるのでしょうか? 回避または解決する方法があるのでしょうか? すみませんが、教えて下さい。

  • Fedora Core2のインストールについて

    Linuxを触ってみようと昨日FedoraCore2の本を買い、本の説明通りインストールを行いました。 インストールが完了し、再起動後「ようこそ」の画面が表示されるはずなのですが、以下の画面からまったく処理が進みません。 Booting 'Fedora Core (2.6.5-1.358)' root (hd0,0) Filesysytem type is ext2fs, partition type 0x83 kernel /vmlinuz-2.6.5.1.358 ro root=LABEL=/rhgb quiet [Linux-bzImage, setup=0x1400, size=0x1235b7] initrd/initrd-2.6.5-1.358img [Linux-initrd @ 0x13ea1000, 0x2ef48bytes] 何度かインストールを繰り返してますが同じ現象です。 GRUBの画面に表示されているのはFedoraCoreだけで 他のOSは入れてません。 何かご存知の方がいらっしゃいましたらお教え願います。 「これかな?」という内容でも結構ですので宜しくお願い致します。

  • VMWare上のkernel再構築

    VMWare 上のRedHat9でカーネルの再構築(練習)で失敗しています。お助けください。 現在のカーネル2.4.20に2.4.23を追加する。 make mrproper make menuconfig make bzImage make modules make modules_install 以上完了 /boot/grub/grub.confは次のようになっています # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/hda2 # initrd /initrd-version.img #boot=/dev/hda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz title Red Hat Linux (2.4.20-8) root (hd0,0) kernel /vmlinuz-2.4.20-8 ro root=LABEL=/ hdc=ide-scsi initrd /initrd-2.4.20-8.img これに追加して title Red Hat Linux (2.4.23) root (hd0,0) kernel /vmlinuz-2.4.23 ro root=LABEL=/ hdc=scsi initrd /initrd-2.4.20-8.img を記述して再起動し2.4.23を選択するとdmssgの途中で NET4:Unix domain sockets1.0/SMP for Linux NET4.0 ds:no socket driver loaded VFS:Cannot open root device "/LABEL=/" or 00:00 Kernel panic:VFS:Unable to mount root fs on 00:00 で停止します。 kernel /vmlinuz-2.4.23 ro root=/dev/hda1 (註/bootパーティション) としてもdmesgは停止位置はほぼ同じで内容は以下のとおりです。 Kernel panic:No init found.Try passing=option to karnel 何かヒントを頂けるとありがたいのですが・・・よろしくお願いします。