FreeBSDでサーバー移行、Xorg設定コピー時のエラー解決方法

このQ&Aのポイント
  • FreeBSDでサーバーを移行し、Xorgを設定ファイルをコピーしてGUIで操作しようとしたところ、エラーが発生しました。
  • Xorgのバージョンや設定ファイルの場所、必要なドライバーのインストール方法などを確認してみてください。
  • また、NVIDIAのドライバーをインストールする際にもエラーが発生しているようです。kernelのソースツリーが見つからないというエラーが出ているので、kernelのソースツリーをインストールし、再度試してみてください。
回答を見る
  • ベストアンサー

こんにちはFreeBSDにサーバーを移行したいと

FreeBSDでサーバーを移行したいのです それでメインPCなのでGUIでやりたいと思い、Xorgを入れて設定ファイルをコピーしました そしてstartxと打つとエラーが出ますログも載せておきます X.Org X Server 1.7.7 Release Date: 2010-05-04 X Protocol Version 11, Revision 0 Build Operating System: FreeBSD 9.0-RC2 amd64 Current Operating System: FreeBSD iroiro.sytes.net 9.1-RELEASE FreeBSD 9.1-RELEA SE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 root@farrell.cse.buffalo.edu:/us r/obj/usr/src/sys/GENERIC amd64 Build Date: 15 October 2012 03:00:20PM Current version of pixman: 0.24.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Mon Mar 25 06:30:12 2013 (==) Using config file: "/etc/X11/xorg.conf" (**) | |-->Monitor "Monitor0" (**) | |-->Device "Card0" (**) |-->Input Device "Mouse0" (**) |-->Input Device "Keyboard0" (==) Automatically adding devices (==) Automatically enabling devices (**) FontPath set to: /usr/local/lib/X11/fonts/misc/, /usr/local/lib/X11/fonts/TTF/, /usr/local/lib/X11/fonts/OTF, /usr/local/lib/X11/fonts/Type1/, X.Org ANSI C Emulation: 0.4 X.Org Video Driver: 6.0 X.Org XInput driver : 7.0 X.Org Server Extension : 2.0 (--) Using syscons driver with X support (version 2.0) (--) using VT number 9 (--) PCI:*(0:1:0:0) 10de:1244:1462:2368 NVIDIA Corporation GF116 [GeForce GTX 55 0 Ti] rev 161, Mem @ 0xf4000000/33554432, 0xe0000000/134217728, 0xe8000000/67108 864, I/O @ 0x0000e000/128, BIOS @ 0x????????/65536 (II) "extmod" will be loaded. This was enabled by default and also specified in the config file. (II) "dbe" will be loaded. This was enabled by default and also specified in the config file. (II) "glx" will be loaded. This was enabled by default and also specified in the config file. (II) "record" will be loaded. This was enabled by default and also specified in the config file. (II) "dri" will be loaded. This was enabled by default and also specified in the config file. (II) "dri2" will be loaded. This was enabled by default and also specified in th e config file. (II) LoadModule: "dbe" (II) Loading /usr/local/lib/xorg/modules/extensions/libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 1.7.7, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "dri" GeForce GT 320M, GeForce GT 240M, GeForce GT 325M, Quadro FX 880M, GeForce G210, GeForce 205, GeForce 310, ION, GeForce 210, GeForce 310, GeForce 315, GeForce G105M, GeForce G105M, NVS 2100M, NVS 3100M, GeForce 305M, ION, GeForce 310M, GeForce 305M, GeForce 310M, GeForce 305M, GeForce G210M, GeForce 310M, Quadro FX 380 LP, Quadro FX 380M, GeForce GT 330, GeForce GT 320, GeForce GT 240, GeForce GT 340, GeForce GT 330, GeForce GTS 260M, GeForce GTS 250M, GeForce 315, GeForce GT 335M, GeForce GTS 350M, GeForce GTS 360M, Quadro FX 1800M (II) Primary Device is: PCI 01@00:00:0 (WW) NV: Ignoring unsupported device 0x10de1244 (GF116 [GeForce GTX 550 Ti]) at 01@00:00:0 (EE) No devices detected. Fatal server error: no screens found Please consult the The X.Org Foundation support at http://wiki.x.org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional informati on. これがログです GTX550tiドライバーを入れようとするとまたしてもエラーが出ました [root@iroiro ~]# tar xzf NVIDIA-FreeBSD-x86_64-310.40.tar.gz && cd NVIDIA-FreeBSD-x86_64-310.40 && make install ===> src (install) "/usr/share/mk/bsd.kmod.mk", line 12: "can't find kernel source tree" *** [realinstall] Error code 1 Stop in /root/NVIDIA-FreeBSD-x86_64-310.40. どうすれば解決するでしょう

質問者が選んだベストアンサー

  • ベストアンサー
  • trapezium
  • ベストアンサー率62% (276/442)
回答No.1

> "/usr/share/mk/bsd.kmod.mk", line 12: "can't find kernel source tree" とりあえずカーネルソースツリーが見つかんないって言ってんだから、それを用意してやってみたら? というか README か INSTALL とかドキュメント入ってない?

kousuke20011016
質問者

補足

すいません自己解決いたしました またごちゃごちゃして再インストールしたら今度は 全く別のエラーが出ましたstartxすると xxxxxx unsupported file layout みたいなのが出ました lsをしてもそんな感じのがでました この件は簡単そうなので自己解決いたします 回答ありがとうございました

関連するQ&A

  • FreeBSD 8.0-p2にXウインドウをインストール

    FreeBSD 8.0-p2にXウインドウをインストール FreeBSD 8.0-p2にXウインドウをインストールするところでツマヅイテオリマス. 手順の概要は以下の通りですが,いかがすればよいでしょうか?? なお,手順の前にはcvsupでsrcとportsはアップデートしております. 1. /usr/ports/x11/xorgに移動 make config-recursive を行い,make 2. make PREFIX0=... install clean を実行するも.pkg-config関連でエラー 3. pkg-configをportsからインストール make make PREFIX=... install clean 4. 再度xorgにインストールを試みる. make PREFIX=... install clean エラーになり,メッセージ通り下記を行う make PREFIX0=... deinstall clean make PREFIX0=... reinstall clean またエラーになり,メッセージ通り下記を行う setenv FORCE_PKG_REGISTER yes make PREFIX=... install clean またまたエラーが出たので下記の通りシェルにパスを設定 setenv PKG_CONFIG_PATH (pkg-configのパス)/libdata 5. 再々度xorgのインストールを試みる. コレまでよりは進んだが,下記のエラーが... ./configure: 12276: Syntax error: word unexpected (expecting ")") ===> Script "configure" failed unexpectedly. Please report the problem to x11@FreeBSD.org [maintener] and attach the "usr/ports/x11/libX11/work/libX11-1.2.1/config.log" including the output of the failure of your make command. Also, it might be a good idea to provide an overview of all packeages installed on your system (e.g. an ls '/var/db/pkg') ここから先が分かりません... 最後のメッセージにあるように,packagesを全てインストールするというのが鍵でしょうか? それはイカにすればよいのでしょうか? また,usr/ports/x11/libX11/work/libX11-1.2.1/config.log を見ると, conftest.c:10:28: error: ac_nonexistent.h: No such file or directory のエラーがありました. とにかくxを入れたいのでアドバイスよろしくお願いします... またパッケージでは8.0-p2がFTPサイトでは無いといわれたのでports でおこなっております. よろしくお願いいたします.

  • FreeBSD(98)8.2R のXの設定について

    仕様機種:PC-9821Ra43 , OS:FreeBSD(98) 8.2R driver : trident $ startx xauth: file /home/umiboz/.serverauth.1219 does not exist xauth: (argv):1: bad display name "chacha:0" in "list" command xauth: (stdin):1: bad display name "chacha:0" in "add" command X.Org X Server 1.7.7 Release Date: 2010-05-04 X Protocol Version 11, Revision 0 Build Operating System: FreeBSD 8.2-RELEASE pc98 Current Operating System: FreeBSD chacha 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Fri Feb 18 05:25:24 UTC 2011 root@asuna:/usr/obj/pc98/usr/src/sys/GENERIC pc98 Build Date: 15 January 2012 10:45:10PM Current version of pixman: 0.24.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Jan 17 23:43:22 2012 Primary device is not PCI (==) Using default built-in configuration (21 lines) (EE) LoadModule: Module fbdevhw does not have a fbdevhwModuleData data object. (EE) Failed to load module "fbdevhw" (invalid module, 0) (EE) No devices detected. Fatal server error: no screens found Please consult the The X.Org Foundation support at http://wiki.x.org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. xinit: giving up xinit: unable to connect to X server: Connection refused xinit: server error xauth: (argv):1: bad display name "chacha:0" in "remove" command $ exit exit Script done on Tue Jan 17 23:43:41 2012 ---- 以上のようなエラーが発生して、Xが立ち上がりません。解決策をご存じの方、ご一報下さると、有り難いです。 よろしくお願いします。

  • WACOMのタブレットがうまく動きません

    CentOS 5.1でWACOMのタブレットを使おうとしているのですが、 うまく動いてくれません。 Linux Wacom Projectのサイトをみながら ドライバのインストールを試みたりしてみたのですが、 うまく動きません。 とりあえずペンの動きにはマウスカーソルが反応します。 しかし本当にとりあえず反応するだけです。 タブレット付属のマウスには反応してくれません。 xorg.confの設定はLinux Wacom Projectを 参考に設定しました。 私はXが悪いのではないかと推測しています。 $ grep -i wacom /var/log/Xorg.0.log (II) LoadModule: "wacom" (II) Loading /usr/lib64/xorg/modules/input/wacom_drv.so (II) Module wacom: vendor="X.Org Foundation" (II) UnloadModule: "wacom" (II) Unloading /usr/lib64/xorg/modules/input/wacom_drv.so (EE) Failed to load module "wacom" (module requirement mismatch, 0) (EE) No Input driver matching `wacom' (EE) No Input driver matching `wacom' (EE) No Input driver matching `wacom' (EE) No Input driver matching `wacom' の様なエラーがログに出力されていましたので。 しかし対処方法がわかりません。 $ uname -a Linux hostname 2.6.18-53.1.4.el5 #1 SMP x86_64 x86_64 x86_64 GNU/Linux WACOM Intuos PTZ-930 X Window System Version 7.1.1 です。 私の推測通りXが原因なのかあるいはそれ以外なのかわかりませんが、 アドバイスをいただけませんでしょうか。 よろしくお願いします。

  • FreeBSD 9.0 startx→再起動

    初めまして、お世話になります。 FreeBSD 9.0(※)でxorgインストール後、startxをすると再起動してしまいます。 (※FreeBSD 9.1のLive CDからのインストールはうまくいきませんでした) /var/log/Xorg.0.logを見ると以下のようなエラーが確認されました。 (EE) Error compiling keymap (server-0) (EE) XKB: Couldn't compile keymap XKB: Failed to compile keymap Keyboard initialization failed. This could be a missing or incorrect setup of xkeyboard-config. Fatal server error: Failed to activate core devices. 下記にあるサイト(1)を参考にして、/etc/X11/xorg.confの各セクションには以下を追記しました。 ・Section "ServerFlags" Option "DontZap" "off" ・Section "Files" FontPath "usr/local/lib/X11/fonts/bitstream-vera/" ・Section "Module" Load "freetype" ・Section "InputDevice" (キーボードの方) Option "XkbRules" "xorg" Option "XkbModel" "jp106" Option "XkbLayout" "jp" Option "XkbOptions" "ctrl:swapcaps" ・Section "InputDevice" (マウスの方) Option "Emulate3Buttons" ・Section "Screen" DefaultDepth 24 (Monitor "Monitor0"の下に挿入) Modes "1280x1024" (Depth 24の下に挿入) ちなみにSection "Monitor"は以下のようになってます。 #DisplaySize 340 270 # mm Identifier "Monitor0" VendorName "DEL" ModelName "DELL 1704FPV" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 Option "DPMS" また、usr/local/etc/hal/fdi/policy/10-x11-kbd.fdiはサイト(2)のII-3の内容をそのまま作り、 /usr/local/share/hal/fdi/policy/10osvendor/10-x11-input.fdi をサイト(1)の中ほどにあるように追記しました。 さらに/etc/rc.confは以下のようになってます。コメントは省略してます。 hostname="localhost" keymap="jp.106.kbd" ifconfig_ue0="DHCP" sshd_enable="YES" moused_enable="YES" ntpd_enable="YES" powerd_enable="YES" dbus_enable="YES" hald_enable="YES" #polkitd_enable="YES" (起動時にfailするのでコメントアウト) canna_enable="YES" dumpdev="NO" sendmail_enable="NO" sendmail_submit_enable="NO" sendmail_outbound_enable="NO" sendmail_msp_queue_enable="NO" ちなみにこのPCのスペックは以下の通りです。 PC型番 : IBM Aptiva 2188-47J M/B : ACER V66LTS CPU : Intel Celeron 466MHz メモリ : 64MB + 64MB HDD : 8GiB SDHC → SD/IDE変換基板を使用 BIOS : Phoenix V3.2 USBポート x2(多分1.1、うち1つにはBuffalo LUA3-U2-ATXでLANに接続) LANポートがなくモジュラーを差し込むジャックが2つ FD&CDドライブ有り ディスプレイ : DELL 1704FPV (D-Sub15ピンケーブルで接続) キーボード : IBM KB-9930 REV.C01 マウス : IBM MO09K (3つ釦マウスでマウスホイール?付き) ビデオメモリはメインメモリと共有かもしれません。詳細は不明 さらに参照したサイトです サイト(1) : http://www.koganemaru.co.jp/Xorg.html サイト(2) : http://silversack.my.coocan.jp/bsd/lxde09x-buildlxde.htm#lxde サイト(3) : http://www.freebsd.org/doc/ja_JP.eucJP/books/handbook/x-config.html 以上ですが、誤設定あるいは設定不足でしょうか? 目標として(PCのスペックが貧弱であるため)、w3m・Canna Server・kinput2・ktermを インストールして、twmでネット閲覧することを考えてます。 FreeBSDには初心者で手探りでやっており、皆様から何かしらのヒントでも頂ければ幸いです。

  • CentOS X Window Systemエラー

    CentOS6.2をインストールして問題なくstartxでデスクトップを使えていたのですが、 yum updateで6.4にアップデートし再起動して startxするとエラーが出てX Window Systemが起動しなくなりました。 CentOS6.4 32bit カーネルはkernel-2.6.32-358.6.1.el6.i686です。 X Window Systemのログファイルを開いて(EE)の部分だけ抜出しました。 明らかに(EE) open /dev/fb0: No such device が気になるのでstatxと一緒にググってみると http://kaki03.blog10.fc2.com/blog-entry-13.htmlさんのような記事がありましたが意味が分かりませんでした。 X Window Systemが起動しない方の記事が他にもたくさん見つかりましたが、それぞれ原因が違うようで ビデオカードが認識できないことによるエラーだという記事はたくさん見つかりましたが、 以下のエラーにはビデオカード辺りぽいエラーが見つからないのでこれには該当しないのかなとも思います。 どなたかお判りの方はいせんでしょうか?ちょっとお手上げ状態です。 ハードウェアには全く詳しくないですがよろしくお願いします。 ■/var/log/Xorg.0.log(X Windows Systemのログ)■ (EE) open /dev/fb0: No such device (EE) Backtrace: (EE) 0: /usr/bin/X (xorg_backtrace+0x50) [0x80b19d0] (EE) 1: /usr/bin/X (0x8048000+0x6f426) [0x80b7426] (EE) 2: (vdso) (__kernel_rt_sigreturn+0x0) [0x72440c] (EE) 3: /usr/lib/xorg/modules/drivers/sis_drv.so (0x3fd000+0x4fdad) [0x44cdad] (EE) 4: /usr/lib/xorg/modules/drivers/sis_drv.so (0x3fd000+0x35ad9) [0x432ad9] (EE) 5: /usr/lib/xorg/modules/drivers/sis_drv.so (0x3fd000+0x292d3) [0x4262d3] (EE) 6: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x56e2) [0x4b16e2] (EE) 7: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x5f04) [0x4b1f04] (EE) 8: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x601b) [0x4b201b] (EE) 9: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x6a9a) [0x4b2a9a] (EE) 10: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x2451) [0x4ae451] (EE) 11: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x9adf) [0x4b5adf] (EE) 12: /usr/lib/xorg/modules/libexa.so (0x4ac000+0xac1d) [0x4b6c1d] (EE) 13: /usr/lib/xorg/modules/libexa.so (0x4ac000+0x96c1) [0x4b56c1] (EE) 14: /usr/bin/X (miPolyRectangle+0x107) [0x81f8e97] (EE) 15: /usr/bin/X (0x8048000+0x140b62) [0x8188b62] (EE) 16: /usr/bin/X (0x8048000+0x2d1a5) [0x80751a5] (EE) 17: /usr/bin/X (0x8048000+0x30d25) [0x8078d25] (EE) 18: /usr/bin/X (0x8048000+0x7a7dc) [0x80c27dc] (EE) 19: /lib/libc.so.6 (__libc_start_main+0xe6) [0x554ce6] (EE) 20: /usr/bin/X (0x8048000+0x1e101) [0x8066101] (EE) (EE) Segmentation fault at address 0x0 Fatal server error: Caught signal 11 (Segmentation fault). Server aborting (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.

  • jp-106のキーボードを使用するには?

    宜しくお願い致します。初心者質問でスイマセン。 CPU: Duron700MHz。 RAM: DDR2100 256MB (128MB+128MB)。 M/B: ECS K7S6A A7V8X-MX-UAY。 VGA: AOpen GeForce2mx 32MB。 のマシンに FreeBSD-5.3-RELEASE.iso をインストールしました。 # hostname hoge.foo.dyndns.net # uname -a FreeBSD hoge.foo.dyndns.net 5.3-RELEASE FreeBSD 5.3-RELEASE #0: Fri Nov 5 04:19:18 UTC 2004 root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386 キーボードの[@]キーを何故か押すと「[」が表示されてしまいます。 一応、コンフィグファイルを探してみました。 /etc/X11/XF86Config-4 /etc/X11/XF86Config /etc/XF86Config /usr/X11R6/etc/X11/XF86Config.ホスト名 /usr/X11R6/etc/X11/XF86Config-4 /usr/X11R6/etc/X11/XF86Config /usr/X11R6/lib/X11/XF86Config.ホスト名 /usr/X11R6/lib/X11/XF86Config-4 /usr/X11R6/lib/X11/XF86Config は無く、 /usr/X11R6/lib/X11/XF86Config.98 /usr/X11R6/lib/X11/XF86Config.eg を発見しました。 どうすればjp-106のキーボードを使用できるのでしょうか?

  • X Window Systemが起動しない

    Debianをインストールしましたが、GUIが起動しません。 ためしに、CUIなのでログインし、「startx」としたところ、、 X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny3) Current Operating System: Linux buffalo 2.6.26-2-686 #1 SMP Thu Jan 27 00:28:05 UTC 2011 i686 Build Date: 25 September 2010 12:05:44PM Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Mon May 2 21:28:57 2011 (==) Using config file: "/etc/X11/xorg.conf" (II) Module "ramdac" already built-in (II) Module "ddc" already built-in (EE) SIS(0): ************************************************** (EE) SIS(0): ERROR: (EE) SIS(0): Virtual screen too big for memory; 4800K needed, 4096K available (EE) SIS(0): END OF MESSAGE (EE) SIS(0): ************************************************** (EE) Screen(s) found, but none have a usable configuration. Fatal server error: no screens found giving up. xinit: Connection reset by peer (errno 104): unable to connect to X server xinit: No such process (errno 3): Server error. とでてきました。 どうすれば起動するのでしょうか? Debian 5.0.3 lenny メモリ 256MB HDD 40GB 一応、VNCをインストールしてWindowsから操作はできるようになっています。 (しかし、タスクバーなどが表示されていません。) 宜しくお願いします。

  • portsの依存関係確認について

    FreeBSD 6.2R を利用しており、過去に cvsup にて ports を最新化した事があります。 ports 導入に際し依存関係を確認しようと下記コマンドを実行しました。 ------------------------------------------------------ # cd /usr/ports/x11/xorg # make pretty-print-run-depends-list This port requires package(s) "" to run. # make pretty-print-build-depends-list # ------------------------------------------------------ xorg は依存関係あるはずなのですが... 試しに下記のコマンドを打つと下記のような結果となります。 ------------------------------------------------------ # make run-depends-list /usr/ports/graphics/dri /usr/ports/x11-drivers/xorg-drivers /usr/ports/x11-fonts/xorg-fonts /usr/ports/x11-servers/xorg-server /usr/ports/x11-themes/xcursor-themes /usr/ports/x11/xbitmaps /usr/ports/x11/xorg-apps /usr/ports/x11/xorg-docs /usr/ports/x11/xorg-libraries # ------------------------------------------------------ INDEX ファイルの問題かと思い portsnap で最新化しました。 ------------------------------------------------------ # portsnap fetch # portsnap extract # portsnap update ------------------------------------------------------ 再度、pretty-print-run-depends-list を行うも変化なしです。 /usr/ports で make index や、portupgrade を入れて、 portsdb -Uu を行うもエラーがでてしまいます。 ------------------------------------------------------ # cd /usr/ports # make index Generating INDEX-6 - please wait..Unknown modifier 'u' Unknown modifier 'u' Unknown modifier 'u' Unknown modifier 'u' Unknown modifier 'u' Syntax error: "||" unexpected ===> arabic/ae_fonts_mono failed *** Error code 1 Unknown modifier 'u' Unknown modifier 'u' Unknown modifier 'u' Unknown modifier 'u' Unknown modifier 'u' Syntax error: Unterminated quoted string ===> accessibility/accerciser failed *** Error code 1 2 errors ******************************************************************** Before reporting this error, verify that you are running a supported version of FreeBSD (see http://www.FreeBSD.org/ports/) and that you have a complete and up-to-date ports collection. (INDEX builds are not supported with partial or out-of-date ports collections -- in particular, if you are using cvsup, you must cvsup the "ports-all" collection, and have no "refuse" files.) If that is the case, then report the failure to ports@FreeBSD.org together with relevant details of your ports configuration (including FreeBSD version, your architecture, your environment, and your /etc/make.conf settings, especially compiler flags and WITH/WITHOUT settings). Note: the latest pre-generated version of INDEX may be fetched automatically with "make fetchindex". ******************************************************************** *** Error code 1 Stop in /usr/ports. *** Error code 1 Stop in /usr/ports. ------------------------------------------------------ 誰か解決策を教えて頂けませんでしょうか。 宜しくお願い致します。

  • FreeBSD 5.3のメールトラブルシューティング

    初めまして。よろしくお願い致します。 自宅サーバにてメールサーバーを運用していたのですが、HDDが壊れてしまった為、HDDを交換し、従来はFreeBSD 4.8でしたが、今回はFreeBSD 5.3をインストールしました。 その後、Portsにて、postfix2.1とqpopperをインストールしたのですが、メールでのやり取りがうまくいかないのです。 現象としては、 ・外部(internetなど)にwebminなどで送信はできるが、受信できない。 ・qpoperにてクライアントPCからメールの送受信が一切できない。 メールのログ(maillog)を見たところ、以下の表示が出ていました。 Oct 22 00:56:57 *** postfix/master[42973]: warning: /usr/local/libexec/postfi x/local: bad command startup -- throttling Oct 22 00:57:04 *** postfix/smtpd[55445]: fatal: open database /etc/aliases.d b: No such file or directory Oct 22 00:57:05 *** postfix/master[42973]: warning: process /usr/local/libexe c/postfix/smtpd pid 55445 exit status 1 Oct 22 00:57:05 *** postfix/master[42973]: warning: /usr/local/libexec/postfi x/smtpd: bad command startup -- throttling aliases.dbがないという記述は分かるのですが、それいがいの意味合いが今一つわからず、困っております。 aliases.dbファイルも探してみたものの、見つかりません。 aliasesというファイルがあったのですが、これの事でしょうか? 他に確認が必要な点がありましたら、御指摘をお願い致します。 以前の4.8はここまで手間取らなかった為、5.0以降設定が何か変わったのでしょうか? どなたかお力を御貸し願います。

  • PPC版のLinux mintでグラフィック不具合

    PowerBookG4でLinx minを動かしたいと思い、 http://www.mintppc.org/content/installation-instructions-mintppc-11 でisoをダウンロードして、起動したところ、 「GONME3を読み込むのに失敗しました。残念ながら、GNOME3が正しく起動せず、フォールバックモードで起動しました。」というエラーがでました。 現在は、GNOME classicで起動しているようなのですが、色数が16色モード?になっているようで、グラフィックが正常に表示されません。 Xorg.o.logの状態は下記の通りです。 # grep -i framebuffer /var/log/Xorg.0.log (II) FBDEV: driver for framebuffer: fbdev (==) FBDEV(0): Depth 8, (==) framebuffer bpp 8 (II) FBDEV(0): checking modes against framebuffer device... (**) FBDEV(0): using shadow framebuffer わからないに、下記の3通りの方法に挑戦しましたが、改善できませんでした。 何かアドバイスがありましたら、お願いいたします。 ●Xorg.confを編集すればよいらしいのですが、Xorg.confがありませんでした。 そこで、 http://mac.linux.be/content/xorgconf-file-powerbook-g415-12-lucid-lynx から、Xorg.confをコピーして、/etc/X11/に「Xorg.conf」という名前でコピーして再起動したのですが、うまくうごきません。 ●次に、NVIDIA GeForce4 420 Goのドライバを探しに、 NVIDIAのページでドライバを探したのですが、適当なものが見つかりませんでした。 ●次に、apt-getでインストールできるアプリはないか? http://www.atmarkit.co.jp/flinux/rensai/linuxtips/636searchaptpk.html を参考に、PowerBookG4のグラフィックカード名「NVIDIA」「GeForce」などの名称でアプリをさがしたのですが、見つかりませんでした。 PowerBookで、lubuntuやxubuntuを動かすことはできているのですが、 サスペンドやレジュームなど電源関係が正常に動作しないので (正常に終了しなかったり、うまく復帰できないので、毎回、再起動しなくてはいけない)、 できれば、Linux mintを動かしたいと思っています。 よろしくお願いいたします。

専門家に質問してみよう