• 締切済み

ブルースクリーンが出たですが、リカバリしないと駄目ですかね…(長文になります)

ブルースクリーンに出たメッセージは下記の通りです。 A problem has been detected and windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: VETEFILE.SYS PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components, restart Your computer, press F8 to select Advanced startup options, and then select safe Mode. Technical information: *** STOP: 0x00000050 (0xE2BC4000,0x00000000,0xED9D98AD,0x00000001) *** VETEFILE.SYS – Address ED9D98AD base at ED9D3000, Datestamp 468de154 ネットをしてる時にいきなりブルースクリーンになりました。 度々、ネットしてる時に勝手にページが閉じる現象が起きたりします。 最近、リカバリしたばかりなのでなるべくならリカバリしたくないですが 他に方法ありましたら、教えて下さい。宜しくお願いします。 最近リカバリした理由は 起動はするですが立ち上がるのがすごく遅く、 トップ画面までは行くですがインターネットのアイコンをクリックすると 立ち上げようとしてるですが「ジジジジー…」と ずっと音してるだけで全然開かなかったのでリカバリしました。 後、メモリーの増設しました。736MBになりました。 ノート型 FMV-BIBLO NB14B(2002年12月購入) システム Windows XP Home Edition      Version 2002 Service Pack2

みんなの回答

  • masa5709
  • ベストアンサー率54% (272/497)
回答No.2

数年前に同じ事になったのですが、私の場合は増設したメモリを取り外したら直りました。 修理に出せばなんとかなるのは当たり前ですが、参考URLの処置法も参考にしてみてください。

参考URL:
http://www.geocities.co.jp/SiliconValley-SanJose/3220/diary060207.htm
  • violet430
  • ベストアンサー率36% (27472/75001)
回答No.1

ハードウェア障害だと思います。 修理を依頼して下さい。

-namie-
質問者

補足

回答して頂きありがとうございます。 昨日、電気店の店員にブルースクリーンに出たメッセージを見せたら、 とにかくリカバリかけろと言われ、それでも駄目なら ハードウェアが駄目なのかもしれませんと言われました。 パソコン本体は持っていきませんでした。 パソコン本体を見せれば、ハードウェアが駄目か分かるですかね…。

関連するQ&A

  • ブルースクリーンエラー

    少し前に質問させてもらったのですが、やはりまだ頻繁にでるので質問させてください。 ログをとったので対処法を教えてもらえないでしょうか? よろしくお願いします PAGE_FAULT_IN_NONPAGAED_AREA If this is the first time you're seen this stop error screen,restart your computer,If this screen appears again,fallow these steps: check to make sure any new hardware or software is properly installed. Ifthis is a new istallation,ask yore hardware or software manufacturer for any windows updates you mightneed. If problems continue,disable or remore any newly installed hardware or software,Disable BIOS memory options such as caching or shadowing. If you need touse sofeMode to remove or disable components,restart your computer,press F8 to select Advanced startup options,and then select safeMode. Technical in for mationi *** Stop:0x00000050(0xBAO0154,040000000,0x8058388F,0x00000000)

  • ブルースクリーン現象になりました

    質問をさしてもらい ブルースクリーン現象ということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x9589a9b8, 0x00000002, 0x00000000, 0x82ebb60b) *** ntkrnlpa.exe - Address 0x82e4ffd9 base at 0x82e02000 DateStamp 0x4cb710d6 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x00000000, 0x0000001b, 0x00000000, 0x82e95c94) *** ntkrnlpa.exe - Address 0x82e9bfd9 base at 0x82e4e000 DateStamp 0x4cb710d6 三つめ A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe CACHE_MANAGER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information:

  • ブルースクリーンが起こってしまったのですが

    質問をさしてもらい ブルースクリーンということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: USBPORT.SYS DRIVER_IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x000000d1 (0x0000008c, 0x00000002, 0x00000000, 0x8fbc62c4) *** USBPORT.SYS - Address 0x8fbc62c4 base at 0x8fbc0000 DateStamp 0x49e01fcf 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntkrnlpa.exe IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x00000063, 0x0000001b, 0x00000001, 0x82ec15ce) *** ntkrnlpa.exe - Address 0x82e67fd9 base at 0x82e1a000 DateStamp 0x4cb710d6 三つめ A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: Ntfs.sys NTFS_FILE_SYSTEM If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000024 (0x001904aa, 0xbf7b7a18, 0xbf7b7714, 0x82ebe22c) *** Ntfs.sys - Address 0x8b41cfff base at 0x8b403000 DateStamp 0x49e0192a

  • ブルースクリーンが起こってしまったのですが

    質問をさしてもらい ブルースクリーンということが分かり (対処の仕方がわかりません) BlueScreenView を使い (何個かありましたが数が多かったので何個かはりました) ブルースクリーンのところを抜き出してみました ハードディスクのバックアップはとらなくても大丈夫でしょうか (色々と対処をしてもまた別の原因でブルースクリーンが起こってしまった場合はどうすればよいでしょうか) A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: luafv.sys IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x0000000a (0x6c006160, 0x0000001b, 0x00000001, 0x82ef55ce) *** luafv.sys - Address 0x91be4036 base at 0x91bdb000 DateStamp 0x47918afb 二つ目 A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: tmcomm.sys PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000050 (0xd76c5da4, 0x00000000, 0x807c6d5b, 0x00000002) *** tmcomm.sys - Address 0x8f28ce4b base at 0x8f287000 DateStamp 0x49d4727e

  • ブルースクリーン

    A problem has been detected and windows has been shut down to prevent damage to your computer. IRQL_NOT_LESS_OR_EQUAL If this the first time you've seen this stop error screen,restart your computer. If this screen appears again,follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation,ask your hardware or software manufacturer for any windows updates you might need. If problems continue,disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe Mode to remove or disable components,restart your computer,press F8 to select Advaned Startup options,and then select safe Mode. Technical information: *** STOP:0X0000000A(0X00000054,0X00000002,0X00000001,0X804DDC8E) Beginning dump of physical memory physical memory dump complete. contact your system administrator or technical support group for further assistance. 起動したときに上記のように書いてありました。 意味がわかりません・・・

  • ブルースクリーンが出て・・・

    A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntoskrnl.exe BAD_POOL_HEADER If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x00000019 (0x0000000000000022, 0x0000000000000000, 0x0000000000000000, 0x0000000000000000) *** ntoskrnl.exe - Address 0xfffff80003eba700 base at 0xfffff80003e4a000 DateStamp 0x4d9fdd34 というブルースクリーンが出てたまにPCが落ちます 対処法を教えてくださいお願いします

  • ブルースクリーン

    A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: VIDEOPRT.SYS KERNEL_MODE_EXCEPTION_NOT_HANDLED If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x1000008e (0xc0000005, 0xb7560ad2, 0xf7886164, 0x00000000) *** VIDEOPRT.SYS - Address 0xb7560ad2 base at 0xb755f000 DateStamp 0x41107d08 コレって何の故障ですか?

  • ブルースクリーン

    A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntoskrnl.exe ATTEMPTED_SWITCH_FROM_DPC If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x100000b8 (0xb2cb3490, 0x80ccca48, 0xb35d7000, 0x00000000) *** ntoskrnl.exe - Address 0x824c0246 base at 0x82418000 DateStamp 0x4a77feb3 ↑の様なブルースクリーンが出て困っております。 ntoskrnl.exeが原因なのでしょうが、何が何だか分かりません。 至急解決策をお願いします。

  • ブルースクリーン

    WinXPがウイルスでブルースクリーンが表示される様になってしまいました。 まずはセーフモードから起動するかという画面が表示されるのですが、セーフモードを選んでも起動せずにブルースクリーンが表示されます。 特に重要なデータもないのでOS再インストールしようと思うのですが、DVDドライブ起動をしようとしても同じ画面が表示されてしまいます。もしかしたらBIOSまでおかしくなってしまったのでしょうか? 以下ブルースクリーンの警告文です。 A problem has been detected and windows has been shut down to prevent damage to your computer. PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed.If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode. Technical information: *** STOP: 0×000000050 (0×F78CB800,0×00000001, 0×80583EC5, 0×00000000) フォーマットも辞さないので、何かいい方法ないでしょうか?? よろしくお願いします。

  • ブルースクリーンになった

    たびたびブルースクリーンになりますが、 今回は *** STOP: 0x0000001D(0xB64F736A,0xBACD79B4,0x00000000) 前回は A problem has been detected and wiondows has been shut to down to prevent damage to your computer. ORQL-NOT-LESS-OR-EQUAL If this si thefirst time you`ve seen this stop error screen, restart your computer. If this screen again,follow these steps: check to meke sure any new hardware or spftware is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components,restart your computer, press F8 to select advanced startup option, and then select safe mode. Technical information: *** STOP: 0x0000000A (0x00000010,0x00000002,0x00000001,0x8051873C) beginning dump of physical memory physical memory dump complete. Contact your system administrator or technical support group for further assistance. 教えてください、お願いします。