• 締切済み

andyが再インストールできません

andyを一度アンインストールして、再インストールしようと思いましたが、できません。 「you are running: microsoft windows 7 home premium. virtualization is disabled in your bios. setup can not continue until you turn on intel VT-x oe AMD SVM.」 という表示が出て終了されます。 翻訳サイトで翻訳してみてもよくわかりません。 なぜインストールできないのでしょうか? 分かる方、教えてください! 推測でもかまいませんのでお願いします☆

みんなの回答

  • maiko0318
  • ベストアンサー率21% (1483/6970)
回答No.1

biosってわかりますか? それの設定が合わないって言っているようです。 <仮想化>の項目だそうですが、メインボードの機種名わかりますか? 設定でできるのか、 バージョンアップでできるのか、 それともできないのか、わかりかねます。

kutibeni22
質問者

お礼

ずいぶん前に締め切られた質問に今さらのお礼で申し訳ありません。 色々と余裕がありませんでした(汗) 結局、genymotionを使用する事にしました^^; せっかくご回答いただいたのに放置してしまい、申し訳ありませんでした。 ありがとうございました^^☆

関連するQ&A

  • Vmware Playerでインストールできません

    Vmware Playerでインストールできません。 最初に下記のようなエラーメッセージが出てきます。 どうすればいいのでしょうか? This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host supports Intel VT-x, but Intel VT-x is disabled. Intel VT-x might be disabled if it has been disabled in the BIOS/firmware settings or the host has not been power-cycled since changing this setting. (1) Verify that the BIOS/firmware settings enable Intel VT-x and disable 'trusted execution.' (2) Power-cycle the host if either of these BIOS/firmware settings have been changed. (3) Power-cycle the host if you have not done so since installing VMware Player. (4) Update the host's BIOS/firmware to the latest version. For more detailed information, see http://vmware.com/info?id=152.

  • 無線LANのドライバをインストールしようとしたら・・・

    please select one way to continue install There have existed an older version.Which way do you like to do? Remove all. Overwrite the older version install without remove. と出てきてRemove all.かOverwrite~のどちらかを選択しないといけないようなんですが、英語はどういう意味でしょうか? 翻訳サイトを使って調べたのですが意味がわかりませんでした。

  • 98から2000へインストールできません

    現在、古いパソコンを使っている素人です。Windows98から2000へクリーンインストールしようとインターネットなどで仕方を調べつつ取りかかっていました。4枚の起動ディスクを作成し、フロッピー4枚目の時に突然、青の画面に「The BIOS in this system is not fully ACPI compliant. Please contact your system vendor or visit http://www.hardware-update.com. for an updated BIOS. If you are unable to obtain an updated BIOS or the latest BIOS supplied by your vendor is not ACPI compliant , you can turn off ACPI mode during text mode setup. To do this , simply press the F7 key when you are prompted to install storage drivers. The system will not notify you that the F7 key was pressed - it will silently disable ACPI and allow you to continue your installation.」という文面が現れ、それ以降操作できない状態となっております。どうすれば、きちんとインストールできるのでしょうか?使用しているパソコンはサンヨーのB5ノートパソコンでMBC-G1Vです。アドバイスお願いします。

  • Windows Media Player10のupdete

    Windows Media Player 10の更新プログラムKB891122を、http://www.microsoft.com/downloads/details.aspx?FamilyID=73c2650f-be61-4bd6-8408-1fd6e7827cd8&DisplayLang=ja ↑ここのサイトに行ってダウンロード&インストールしたいんですけど、インストールの途中で、『System Restore is turned off.Ifyou continue Setup.you will be unable to use System Restore to restore the version of Windows Media Player that was included with the Windows operating system that your computer is running.It is recommended that you click Cancel,turn on System Restore,and then upgrade to Windows Media Player 10.For more information about System Restore,see Help and Support.Do you want to continue?』 って出てエラーになっちゃうんです。。(>_<) 翻訳してみたんですけど、続行していいものかイマイチわからなくてキャンセルしちゃいました。。 このまま続行して大丈夫ですか? それか、いったんWindows Media Player10をアンインストールしちゃって、まるごとダウンロードしてきたほうがいいですか? Windows Media Player10 ver 10.00.00.3650 XP SP1Home 宜しくですm(__)m。

  • プリンターのインストール

    すみませんが、W2kでLexmark Z11 のインストールの仕方を教えて下さい。webからソフトをダウンロードしたのはいいのですが、やり方がインストールができません・・・ 説明は Instructions for installing the Lexmark Z11 Printer driver in Windows 2000 1.) Save W2KZ11.exe to your computer (Desktop is recommended) 2.) A.) Double-Click the W2KZ11.exe file on your computer to expand it. Choose Unzip to unzip the file to the C:\LxkZ11 directory. B.) Click Start, Settings, Printers, Add Printer. C.) Follow the instructions on the screen until you are asked to select the manufacturer and model of your printer. Then, click the 'Have Disk' button. D.) Click the Browse button and go to the folder where you expanded the W2KZ11.exe file (the default is C:\LXKZ11). Choose Open, then OK. E.) Lexmark Z11 Series Colorfine should appear. Choose Next. Follow the on-screen instructions. F.) When asked if you wish to print a Test Page, choose No. G.) If you see a message that says "Digital Signature Not Found", choose Yes to continue. The driver will install correctly. H.) After the installation is complete, restart Windows. I.) After Windows Restarts, go to Printer Properties, then click the Cartridge tab to choose the cartridge that is installed in the printer. The Lexmark Z11 is now ready to print! でエキサイト翻訳で翻訳して見て試したのですが、さっぱりなのです…どなたかすみませんが、ご教授ください。 お願いします。

  • Ubuntu13.10をインストールしたのですが

    これからLinuxを使っていこうと思っている初心者ユーザです。 サポート切れのWindows XPを削除し、Ubuntu13.10をインストールしました。 使用機種:PC-AL50FY CPU:モバイル AMD Athlon XP-Mプロセッサ2000+ グラフィックアクセラレータ:VIA/S3 Graphics社製UniChromo メインメモリ:1GBに増設 その結果、インストールは完了できたのですが、再起動後、 「The system is running in low-graphics mode Your screen,graphics cardsand input device settings could not be detected correctly. You will need to configure these yourself.」 のダイアログボックスが表示されます。 <Alt>+<Ctrl>+<F1>を押下して、CUIの画面でユーザログインはできました。 同様の経験をお持ちの方あるいは何か解決方法をご存じの方が いらっしゃいましたらご教授ください。 以上、よろしくお願いします。

  • インストールエラー MachFive2

    MachFive2 という、ソフト音源のインストール時のエラーに関する質問です。 環境は Microsoft Windows XP Professional x64 Edition Version 2003 Service Pack 2 Intel(R) Core(TM) i7 CPU 940 @ 2.93GHz 2.93GHz, 11.9GB RAM まず、インストールウィザードで最初に出てくるウィンドウメッセージが、 「Are you running on a 32-bit version of Windows XP or Vista? Choose Yes for 32-bit, No for 64-bit.」 64 なので No を選ぶと、 「The installer has detected that the required version of the Interlok driver is not installed. The MachFive 2 installer will quit and install the necessary version of the Interlok drivers. When prompted, please restart your computer. After restarting, please run the MachFive 2 installer again with your iLok connected.」 ドライバのバージョンが駄目、みたいなことが書いてあるわけですが、 iLok-key はあるし、そのドライバーも最新のものがインストール済みです。 OK しかないので、OK を押します。すると、 「This setup will perform an upgrade of 'Interlok driver setup x 64' Do you want to continue?」 ドライバをアップグレードするって・・・、もう最新のがあるんだってば;; 続けるかやめるか選ぶわけですが、No だと終わるので、Yes で。。そしたら、 「A later version of 'Interlok driver setup x64' is already installed on this machine. The setup cannot continue.」 x64 の後のバージョンのドライバだから、インストールできない・・・? よくわかりません。32bit Windows では、こんなことはなかった・・・。 64bit の OS に変わってから、ある程度ややこしいことは予想していたものの、 やはり納得ができないエラーが出るわけです。 このソフトは、しっかり 64 に対応しているわけだし。。 同じ経験の人がいるかもしれないので、 確立は低いかもしれませんが、何か情報があることを願っています。 あるいはそうでなくとも、何か小さな手がかりだけでも見つかればと思います。

  • pip install dlib

    windows10 Anaconda3 Anaconda Promptで pip install dlib でインストールできません。 他のライブラリはpipで普通にインストールできています。 初めてライブラリのインストールでエラーになりました。 エラーメッセージはかなりの長文でどこを掲載したらいいのか解らないので最初の白文字だけ掲載します。後は赤文字のオンパレードになっています。 WARNING: pip is being invoked by an old script wrapper. This will fail in a future version of pip. Please see https://github.com/pypa/pip/issues/5599 for advice on fixing the underlying issue. To avoid this problem you can invoke Python with '-m pip' instead of running pip directly. Collecting dlib Using cached dlib-19.19.0.tar.gz (3.2 MB) Building wheels for collected packages: dlib Building wheel for dlib (setup.py) ... error google翻訳で見たのですがよく解りません。 どなたかインストールの方法をよろしくお願いします

  • これは何を尋ねているのでしょうか?

    これは何を尋ねているのでしょうか? XMedia Recodeというフリーソフトをダウンロードしましたが、 ダウンロードする際以下のようなメッセージが表示されました。 「select whether you want to install xmedia recode 2.2.2.0 for yourself only or for all users of this computer.click next to continue.」 という問いに 以下の2つの選択肢がありました 1、install for anyone using this computer 2、install just for me はじめからチェックが入っていたのは1だったので そのまま1でインストールしたのですが、 気になりましたので質問させていただきました。 翻訳サイト利用してみましたが分かりませんでしたので、 お分かりになる方よろしくおねがいします。

  • pylearn2 インストール失敗

    >>python setup.py install を実行した所、 running install Because Pylearn2 is under heavy development, we generally do not advice using the `setup.py install` command. Please consider using the `setup.py develop` command instead for the following reasons: 1. Using `setup.py install` creates a copy of the Pylearn2 source code in your Python installation path. In order to update Pylearn2 afterwards you will need to rerun `setup.py install` (!). Simply using `git pull` to update your local copy of Pylearn2 code will not suffice. 2. When using `sudo` to install Pylearn2, all files, including the tutorials, will be copied to a directory owned by root. Not only is running tutorials as root unsafe, it also means that all Pylearn2-related environment variables which were defined for the user will be unavailable. Pressing enter will continue the installation of Pylearn2 in `develop` mode instead. Note that this means that you need to keep this folder with the Pylearn2 code in its current location. If you know what you are doing, and are very sure that you want to install Pylearn2 using the `install` command instead, please type `install`. Installation mode: [develop]/install/cancel: と、出力されinstallを実行した所、 running build running build_py running build_ext building 'pylearn2.utils._window_flip' extension C compiler: gcc-4.2 -fno-strict-aliasing -fno-common -dynamic -isysroot /Developer/SDKs/MacOSX10.6.sdk -arch i386 -arch x86_64 -g -DNDEBUG -g -fwrapv -O3 -Wall -Wstrict-prototypes compile options: '-I/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/numpy/core/include -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c' gcc-4.2: pylearn2/utils/_window_flip.c i686-apple-darwin10-gcc-4.2.1: pylearn2/utils/_window_flip.c: No such file or directory i686-apple-darwin10-gcc-4.2.1: no input files i686-apple-darwin10-gcc-4.2.1: pylearn2/utils/_window_flip.c: No such file or directory i686-apple-darwin10-gcc-4.2.1: no input files lipo: can't figure out the architecture type of: /var/folders/i0/i013vMBRH8O06CgW9BFy3E+++TM/-Tmp-//ccGQGOMD.out i686-apple-darwin10-gcc-4.2.1: pylearn2/utils/_window_flip.c: No such file or directory i686-apple-darwin10-gcc-4.2.1: no input files i686-apple-darwin10-gcc-4.2.1: pylearn2/utils/_window_flip.c: No such file or directory i686-apple-darwin10-gcc-4.2.1: no input files lipo: can't figure out the architecture type of: /var/folders/i0/i013vMBRH8O06CgW9BFy3E+++TM/-Tmp-//ccGQGOMD.out error: Command "gcc-4.2 -fno-strict-aliasing -fno-common -dynamic -isysroot /Developer/SDKs/MacOSX10.6.sdk -arch i386 -arch x86_64 -g -DNDEBUG -g -fwrapv -O3 -Wall -Wstrict-prototypes -I/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/numpy/core/include -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c pylearn2/utils/_window_flip.c -o build/temp.macosx-10.6-intel-2.7/pylearn2/utils/_window_flip.o" failed with exit status 1 とgcc4.2の部分でエラーが発生しました。 最新のgccは4.9であるため、バージョンによる失敗なんでしょうか? ちなみにdevelopを実行しても同様です。 対応策をよろしくお願い致します。

専門家に質問してみよう